Cisco Systems 12006, 12406 manual PRP Interfaces Using the PRP LEDs

Page 44

Chapter 3 Installing the Router

IOS Software Configuration for the Router

As the router boots the Cisco IOS software image, the console screen displays a system banner similar to the following:

Cisco Internetwork Operating System Software IOS (tm) GS Software (GSR-P-M) 12.0(20020120:204554)

Copyright (c) 1986-2002 by cisco Systems, Inc. Compiled Sat 20-Aug-01 18:34

.

.

.

Note The system banner that appears depends on the image version of the

Cisco IOS software that the system is running.

If the ROM monitor prompt (rommon>) appears on the system console, your router did not find a valid system image, or the boot sequence was otherwise interrupted, and the system entered read-only memory (ROM) monitor mode.

To boot a Cisco IOS software image manually, enter the boot command on the system console. For information on using the various forms of the boot command, see the following sections:

•Locating a Valid Cisco IOS Software Image, page 3-47

•Booting from the Cisco IOS Software Image, page 3-48

PRP Interfaces Using the PRP LEDs

The PRP faceplate has eight device or port LED activity indicators. (See Figure 3-24.) Each LED goes on when its corresponding PCMCIA slot is accessed. The ports are as follows:

•Two PCMCIA slot activity LEDs labeled SLOT-0 and SLOT-1.

•Four RJ-45 Ethernet port activity LEDs. These LEDs are used by the RJ-45 Ethernet connectors. Each connector includes four LEDs that indicate link activity (LINK), port enabled (EN), data transmission (TX), and data reception (RX).

•Two Ethernet port-selection LEDs labeled PRIMARY. These two LEDs, when on, identify which of the two Ethernet connections is selected. Because both ports are supported on the PRP, the LED on port ETH0 is always on. The ETH1 LED goes on when it is selected.

	Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide
3-44	OL-11497-03

Image 44

Contents Installing the Router Installing a Router Tools and Equipment Required Installing the Rack-Mount Brackets OptionalInstalling the Optional Rack-Mount Brackets Installing the Optional Rack-Mount Brackets Installing Center-Mount Brackets Optional Lower and Upper Center-Mount BracketsInstalling the Optional Center-Mount Brackets Repeat through for both upper center-mount bracketsInstalling the Chassis in a Rack Power supplyOL-11497-03 Installing the Chassis on a Tabletop or Flat Surface Supplemental Bonding and Grounding ConnectionsSupplemental Bonding and Grounding Port for Nebs Compliance Connecting RP and Line Card Cables Crimping the LugChassis Cable-Management Bracket Connecting Alarm Card Cables Connecting to the Console and Auxiliary Ports GRP Console and Auxiliary PortsGRP Console DCE and Auxiliary DTE Port Connections Pin Signal Input/Output Description GRP Console Port SignalsGRP Auxiliary Port Signals RTS PRP Console and Auxiliary Ports PRP Console and Auxiliary Port ConnectionsPRP Console Port Signals Console Port Pin Signal Input/Output DescriptionAuxiliary Port Pin Signal Installing a Flash Memory CardPRP Auxiliary Port Signals 10 Flash Memory Card Slot Opening Connecting the GRP to an Ethernet Network 11 RJ-45 and MII Ethernet ConnectionsPin1 Out Input/Output Description Code MDCPin Out Input/Output Description Code PinConnecting the PRP to an Ethernet Network Pin Signal14 Using the Ethernet Port on the PRP Ethernet Port Pin Signal Description PRP Ethernet ConnectionsCrossover Cable Pinout for Connecting Two PRPs Parameter Connecting to an AC Power SourceParameter RJ-45 Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm IOS Software Configuration for the Router Cisco IOS Software ImagesConditions to Check Before System Startup Overview of the Boot Process Starting the Router and Observing Initial ConditionsOL-11497-03 RP Alphanumeric LED Display Meaning SourceRP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH System Configuration Dialogue External Network InterfaceManually Booting the System Dir bootflashLocating a Valid Cisco IOS Software Image Dir slot0Booting from the Cisco IOS Software Image Command DescriptionBefore You Begin Router ConfigurationSetup Command Cisco IOS User Interface User Interface Command ModesGlobal Configuration Mode User Exec Mode Privileged Exec ModeROM Monitor Mode Interface Configuration ModeSubinterface Configuration Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Host Name Configuring Global ParametersPasswords Configuring Network Interfaces ProtocolsGRP Ethernet Interfaces PRP Ethernet InterfacesLine Card Interfaces Router# show version Show version CommandChecking the Software Version Router# show running-config Verifying the Running Configuration SettingsShow running Config Command Example No service tcp-small-servers Hostname Router Saving the Running Configuration Settings to Nvram Reviewing the Running Configuration SettingsShow startup-config Command Router# copy running-config startup-configNo logging trap Using Flash Memory Cards in the RP Installing the Flash Memory Card in a RPRemoving the Flash Memory Card from an RP Formatting a Flash Memory CardRouter# format slot0 Specify a Boot ImageRouter# configure terminal Flash Memory Console Commands Router# cd slot1Router# cd bootflash Router# delete slot0infoRouter# squeeze slot0 Booting from Flash Memory Routerconfig# boot system flash devicefilenameRouterconfig# config-reg Ctrl-Z Copying FilesRouter# copy tftpfilename bootflashslot0slot1 filename Router# copy tftpmyfile1 slot0myfile1Copying a Cisco IOS Software Image Router# copy tftpnew.image slot0new.imageCopying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Router# show bootvar Copy startup-config slot0 slot1filenameRouter# copy startup-config slot0myfile2 Router# dir slot0Copy running-config slot0slot1filename Router# copy running-config slot0myfile2Router# copy startup-config running-config Copy slot0slot1filename startup-configRouter# copy slot0myfile startup-config If You Need More Information Locked Blocks in Flash Memory CardsInstalling the Router If You Need More Information OL-11497-03