Cisco Systems 12406, 12006 manual Power On the Router

Page 35

Chapter 3 Installing the Router

Power On the Router

Power On the Router

To power on the router, follow these steps:

Step 1 Either switch on all the circuit breakers or plug the power cord into an active power source that controls power to the PDU in the router.

During the first-time startup, the system displays the system banner information. Check the startup banner and displays to ensure that the system has restarted properly and that all the interfaces reinitialize properly.

Step 2 Check the power module LEDs. They should appear as described below:

For a router equipped with AC-input power supplies:

Green LED labeled AC—When the power module is fully seated in its bay and is receiving source power within the required range, this LED should be on. It indicates that AC power is present and is within specified limits. The power supply fan should also be on.

Green LED labeled DC—Power supply is operating normally in a powered-on condition.

For a router equipped with DC-input PEMs:

Green LED labeled INPUT OK—When the power module is fully seated in its bay and is receiving source power within the required range, this LED should be on. It indicates that DC power is present and is within specified limits. The power supply fan should also be on.

Green LED labeled OUTPUT OK—DC-input PEM is operating normally in a powered-on condition.

Amber LED labeled MISWIRE—Should be off. When it is on, it indicates that the input is wired backward at the PDU input.

Step 3 Go to the rear of the chassis and visually check the two LEDs on the front of the blower module. They should appear as described below:

Green LED labeled OK—Should be on

Red LED labeled FAIL—Should be off

Step 4 Listen for the blowers in the blower module; you should immediately hear them operating.

 

 

Cisco 12006 and Cisco 12406 Router Installation and Configuration Guide

 

 

 

 

 

 

OL-11497-03

 

 

3-35

 

 

 

Image 35
Contents Installing the Router Installing a Router Tools and Equipment Required Installing the Rack-Mount Brackets OptionalInstalling the Optional Rack-Mount Brackets Installing the Optional Rack-Mount Brackets Lower and Upper Center-Mount Brackets Installing Center-Mount Brackets OptionalRepeat through for both upper center-mount brackets Installing the Optional Center-Mount BracketsPower supply Installing the Chassis in a RackOL-11497-03 Supplemental Bonding and Grounding Connections Installing the Chassis on a Tabletop or Flat SurfaceSupplemental Bonding and Grounding Port for Nebs Compliance Crimping the Lug Connecting RP and Line Card CablesChassis Cable-Management Bracket Connecting Alarm Card Cables GRP Console and Auxiliary Ports Connecting to the Console and Auxiliary PortsGRP Console DCE and Auxiliary DTE Port Connections Pin Signal Input/Output Description GRP Console Port SignalsGRP Auxiliary Port Signals RTS PRP Console and Auxiliary Port Connections PRP Console and Auxiliary PortsConsole Port Pin Signal Input/Output Description PRP Console Port SignalsAuxiliary Port Pin Signal Installing a Flash Memory CardPRP Auxiliary Port Signals 10 Flash Memory Card Slot Opening 11 RJ-45 and MII Ethernet Connections Connecting the GRP to an Ethernet NetworkMDC Pin1 Out Input/Output Description CodePin Pin Out Input/Output Description CodePin Signal Connecting the PRP to an Ethernet Network14 Using the Ethernet Port on the PRP PRP Ethernet Connections Ethernet Port Pin Signal DescriptionCrossover Cable Pinout for Connecting Two PRPs Parameter Connecting to an AC Power SourceParameter RJ-45 Router Power Combination 18 AC Power Distribution Unit Connecting to a DC Power Source DC PDU Power a Power On the Router Alarm Cisco IOS Software Images IOS Software Configuration for the RouterConditions to Check Before System Startup Starting the Router and Observing Initial Conditions Overview of the Boot ProcessOL-11497-03 Display Meaning Source RP Alphanumeric LEDRP Interfaces Using the RP LEDs GRP Interfaces Using the GRP LEDs PRP Interfaces Using the PRP LEDs ETH External Network Interface System Configuration DialogueDir slot0 Manually Booting the SystemDir bootflash Locating a Valid Cisco IOS Software ImageCommand Description Booting from the Cisco IOS Software ImageBefore You Begin Router ConfigurationSetup Command Cisco IOS User Interface User Interface Command ModesGlobal Configuration Mode Privileged Exec Mode User Exec ModeROM Monitor Mode Interface Configuration ModeSubinterface Configuration Mode Configuration Changes Setup Command Interactive Script Example SDCC1/0 Configuring interface POS1/0 Is this interface in use?yes Host Name Configuring Global ParametersPasswords Protocols Configuring Network InterfacesPRP Ethernet Interfaces GRP Ethernet InterfacesLine Card Interfaces Router# show version Show version CommandChecking the Software Version Router# show running-config Verifying the Running Configuration SettingsShow running Config Command Example No service tcp-small-servers Hostname Router Router# copy running-config startup-config Saving the Running Configuration Settings to NvramReviewing the Running Configuration Settings Show startup-config CommandNo logging trap Installing the Flash Memory Card in a RP Using Flash Memory Cards in the RPFormatting a Flash Memory Card Removing the Flash Memory Card from an RPRouter# format slot0 Specify a Boot ImageRouter# configure terminal Router# cd slot1 Flash Memory Console CommandsRouter# delete slot0info Router# cd bootflashRouter# squeeze slot0 Copying Files Booting from Flash MemoryRouterconfig# boot system flash devicefilename Routerconfig# config-reg Ctrl-ZRouter# copy tftpmyfile1 slot0myfile1 Router# copy tftpfilename bootflashslot0slot1 filenameRouter# copy tftpnew.image slot0new.image Copying a Cisco IOS Software ImageCopying Cisco IOS Software Updates Router# copy slot1image.new slot0image.new Copying Files Between RP Memory and a Flash Memory Card Copy startup-config slot0 slot1filename Router# show bootvarRouter# dir slot0 Router# copy startup-config slot0myfile2Router# copy running-config slot0myfile2 Copy running-config slot0slot1filenameRouter# copy startup-config running-config Copy slot0slot1filename startup-configRouter# copy slot0myfile startup-config Locked Blocks in Flash Memory Cards If You Need More InformationInstalling the Router If You Need More Information OL-11497-03