Cisco Systems VIP4 manual Introduction

Page 1

Fourth Generation Versatile Interface Processor (VIP4) Installation and Configuration Guide

Product Numbers: VIP4-50=, VIP4-80=, MEM-VIP4-64M-SD=, MEM-VIP4-128M-SD=, MEM-VIP4-256M-SD=

Introduction

This guide provides instructions for installing, configuring, and maintaining the fourth-generation Versatile Interface Processor (VIP4). The VIP4 operates with the Cisco 7505, Cisco 7507, Cisco

7507-MX, Cisco 7513, Cisco 7513-MX, and the Cisco 7576 routers with the Route Switch Processor (RSP1, RSP2, RSP4, RSP4+, or RSP8), and with the Cisco 7000 series routers using the 7000 Series Route Switch Processor (RSP7000) and 7000 Series Chassis Interface (RSP7000CI). See the “Software Requirements” section on page 9 for specific compatibility requirements.

The VIP4 supports online insertion and removal (OIR), which allows you to remove and replace a VIP4 without first shutting down the system. Online insertion and removal maximizes router availability by letting you add or remove VIP4s during system operation. See the “Guidelines for VIP4 Removal and Installation” section on page 15 for more information on removing and installing the VIP4.

The VIP4 supports LAN and WAN port adapters (PAs), including Fast Ethernet, T1/E1, High-Speed Serial Interface (HSSI), T3/E3, T3/E3 ATM, multichannel T1/E1, multichannel T3/E3, OC-3 ATM, Packet over SONET (POS), and OC-12 ATM. For a list of supported port adapters, refer to the “VIP4 and Port Adapter Compatibility” section on page 7 .

The VIP4 port adapters do not support OIR, so when removing or inserting a port adapter, the system must be shut down first. The VIP42 must be removed from its interface processor slot before removing or installing a port adapter.

For complete descriptions of interface subcommands and the configuration options available for VIP4-related interfaces, refer to the configuration note for each of the port adapters installed on your VIP4 and to the appropriate Cisco IOS software configuration publications. (See the “Related Documentation” section on page 2 .)

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 2002. Cisco Systems, Inc. All rights reserved.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Introduction Related Documentation ContentsHow to Identify the VIP4 Model What is the VIP4?VIP4 Overview Eeprom contents hex Value VIP4 Model Type Size/Speed Description LocationDescription Specifications SpecificationsVIP4 Port Adapter Overview Number Product Number Description Ports VIP4 and Port Adapter CompatibilityPA-8E Software Requirements Installation PrerequisitesProduct Number Description Number of Ports Microcode Overview Hardware RequirementsTraffic Management VIP Release Minimum Cisco IOS Supported ReleasesROM Monitor Overview Agency ApprovalsTools and Parts Required Safety Warnings Safety GuidelinesApprovals Agencies Electrical Equipment Guidelines Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesGuidelines for VIP4 Removal and Installation VIP4 Installation ProceduresVIP4 Installation Procedures Bottom ejector lever Processor module slot Module Handling Interface Processors-Vertical Orientation Shown Removing a VIP4Installing a VIP4 Step Performing a Basic Configuration Checking the VIP4 InstallationVerifying the VIP4 Installation Insertion RemovalChecking the VIP4 Installation Using show Commands to Display Interface Information Using show Commands to Verify the VIP4 StatusRouter# show interfaces fastethernet 1/0/0 Router# show controllers fastethernet 1/0/0 Router# show controllers cbusRouter# show version 00 E1 6B 0C 47 02 Using the ping Command to Verify Network Connectivity VIP4 Maintenance ProceduresUpgrading VIP4 Microcode Router# show flash Routerconfig# microcode vip4 flash slot0vip11-1 Router# configure terminalRouter# copy running-config startup-config Router# copy tftpvip11-1 slot0vip11-1Product Description Upgrading VIP4 MemoryLocation of CPU Memory and Packet Memory DIMMs on the VIP4 Removing Sdram DIMMsOpening the Dimm Socket Tabs Inserting the Dimm Installing Sdram DIMMsInstalling or Replacing a Port Adapter on a VIP4 Checking the VIP4 Memory UpgradeHandling a Port Adapter Single-Width Port AdapterStep Dual-Width Port AdapterLocation of VIP4 Slot Divider and Screws Removing and Installing a Dual-Width Port Adapter Obtaining Documentation VIP4 TroubleshootingWorld Wide Web Documentation CD-ROMDocumentation Feedback Obtaining Technical AssistanceCisco.com Technical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteContacting TAC by Telephone Obtaining Technical Assistance OL-3673-01
Top Page Image Contents