Cisco Systems VIP4 manual Safety Guidelines, Safety Warnings, Approvals Agencies

Page 12

Safety Guidelines

Approvals

Agencies

 

 

Safety

CSA-C22.2 No. 950 (Canada)

 

EN60950 (Europe)

 

IEC 950 (International)

 

UL 1950 (United States)

 

 

Emissions

CE marking (Europe)

 

CISPR 22 Class B (International)

 

FCC Part 15 Class A (United States)

 

EN55022 Class B (Europe)

 

ICES-003 Class A (Canada)

 

VCCI Class B (Japan)

 

 

Safety Guidelines

Following are safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.

Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).

Fourth Generation Versatile Interface Processor (VIP4) Installation and Configuration Guide

12

OL-3673-01

 

 

Image 12
Contents Introduction Contents Related DocumentationWhat is the VIP4? How to Identify the VIP4 ModelVIP4 Overview Eeprom contents hex Value VIP4 Model Location Type Size/Speed DescriptionSpecifications Description SpecificationsVIP4 Port Adapter Overview VIP4 and Port Adapter Compatibility Number Product Number Description PortsPA-8E Installation Prerequisites Software RequirementsProduct Number Description Number of Ports Hardware Requirements Microcode OverviewTraffic Management VIP Release Minimum Cisco IOS Supported ReleasesAgency Approvals ROM Monitor OverviewTools and Parts Required Safety Guidelines Safety WarningsApprovals Agencies Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge DamageVIP4 Installation Procedures Guidelines for VIP4 Removal and InstallationVIP4 Installation Procedures Bottom ejector lever Processor module slot Module Removing a VIP4 Handling Interface Processors-Vertical Orientation ShownInstalling a VIP4 Step Checking the VIP4 Installation Performing a Basic ConfigurationVerifying the VIP4 Installation Removal InsertionChecking the VIP4 Installation Using show Commands to Verify the VIP4 Status Using show Commands to Display Interface InformationRouter# show interfaces fastethernet 1/0/0 Router# show controllers cbus Router# show controllers fastethernet 1/0/0Router# show version 00 E1 6B 0C 47 02 VIP4 Maintenance Procedures Using the ping Command to Verify Network ConnectivityUpgrading VIP4 Microcode Router# show flash Router# configure terminal Routerconfig# microcode vip4 flash slot0vip11-1Router# copy running-config startup-config Router# copy tftpvip11-1 slot0vip11-1Upgrading VIP4 Memory Product DescriptionRemoving Sdram DIMMs Location of CPU Memory and Packet Memory DIMMs on the VIP4Opening the Dimm Socket Tabs Installing Sdram DIMMs Inserting the DimmChecking the VIP4 Memory Upgrade Installing or Replacing a Port Adapter on a VIP4Single-Width Port Adapter Handling a Port AdapterDual-Width Port Adapter StepLocation of VIP4 Slot Divider and Screws Removing and Installing a Dual-Width Port Adapter VIP4 Troubleshooting Obtaining DocumentationWorld Wide Web Documentation CD-ROMObtaining Technical Assistance Documentation FeedbackCisco.com Contacting TAC by Using the Cisco TAC Website Technical Assistance CenterContacting TAC by Telephone Obtaining Technical Assistance OL-3673-01