Cisco Systems Cisco AS5400 quick start Connecting Alarm Device to Cisco AS5350

Page 25

To connect an alarm device to the alarm port, follow this procedure:

Note The alarm connector is a 3-wire connector that plugs into a receptacle in the rear of the chassis. The connector is provided in the accessory kit that ships with the universal gateway.

Step 1 Insert the three-pin alarm port connector (included in the accessory kit) into the alarm port terminal block.

Step 2 Strip a minimum 1/4 in. (0.625 cm) off the wire insulation to connect the stranded wires to the alarm connector. The maximum insulation strip length is 0.31 in. (0.78 cm).

Note Use stranded Number 12 or 14 AWG copper wires to connect an alarm device to the alarm port connector.

Step 3 Secure the wires to the alarm connector with the screws on the connector.

Caution The maximum tightening torque on the screws is 7 in.-lb (0.79 N-m).

Connecting Alarm Device to Cisco AS5350

To alarm device

 

 

 

 

 

#1

 

#3

Cable ties

#2

 

Alarm port connector

35967

Connecting Alarm Device to Cisco AS5400

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

#1

 

#3

Cable ties

#2

 

Alarm port connector

35145

Step 4 Attach two cable ties to the chassis and connect the wires to the cable ties.

Step 5 Attach the alarm wires to the alarm device.

25

Image 25
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways User Documentation Documents, Equipment, and ToolsRelated Hardware Documentation Cisco IOS Software DocumentationSafety Information Install ChassisItems Not Included Rack-Mounting the Chassis Setting Up the ChassisRequired Tools and Equipment Attaching BracketsInstallation in a Rack Desktop InstallationChassis Ground Connection Installing Carrier Cards Install ModulesInstalling a Carrier Card Install the Carrier Card in the Cisco AS5350 Gateway Software Configuration Guide Installing DFCsInstalling a DFC in a Cisco AS5350 State Description DFC LEDT3 DFC Activity ACT Connect CablesWAN, LAN, and Voice Connections System Management and Power ConnectionsConnect a Console Terminal Color or Port or Connection Type Connected to CableConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Device Connect to a WANConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Information document that accompanied this device Connecting Serial Port on Cisco AS5400 to CSU/DSUConnecting Alarm Device to Cisco AS5350 Alarm Pinouts Connect AC PowerThat accompanied this device Connect DC PowerRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a host name for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using CLI Manual ConfigurationGatewayconfig# service password-encryption Gatewayconfig# enable secret guessmeGatewayconfig# service timestamps debug datetime msec Gatewayconfig# service timestamps log datetime msecGateway# configure terminal Configuring Local AAA SecurityGateway# show privilege Configure Basic Dial Access Gatewayconfig# interface group-async Configuring the Asynchronous Group InterfaceGateway# ping Gateway# show async status Gateway# show interface async 4/0Configuring a Channelized T1 or E1 DFC Gateway# show controller t1 1/7 Configuring a Channelized T3 DFCGateway# show controller t3 1/0 Configuring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Gateway# show running-config Gateway# show isdn serviceGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig-if#ip address 172.16.254.254 Gatewayconfig# interface serial 1/023Gatewayconfig-if#isdn incoming-voice modem Gateway# show interface serial 1/023 Configuring the Universal Port Dial Feature Card and LinesSPE Firmware Feature DescriptionAllow all protocols to be used when connecting to the line Gateway# show line Configure ClockingDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 1 externalGatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 3 freeYES Gateway# copy running-config startup-config Saving Configuration ChangesVoice over IP PrerequisitesConfiguration Tasks Where to Go NextSlot Numbering For new features associated with a software releaseObtaining Technical Assistance Cisco TAC Escalation Center Cisco TAC WebsiteObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.