Cisco Systems Cisco AS5350, Cisco AS5400 quick start Connect DC Power, That accompanied this device

Page 27

Connecting AC Power Cord to Cisco AS5400

Power switch

30851

Step 2 Connect the other end of the power cord to the electrical outlet.

Step 3 If your universal gateway has a second power supply installed, repeat Step 1 and Step 2 for the second power supply.

Connect DC Power

Warning

A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. To see translations of

 

 

the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document

 

 

that accompanied this device.

 

 

 

 

 

 

Warning

This product relies on the building’s installation or power supply for short circuit (overcurrent) protection. Ensure

 

 

that a listed and certified fuse or circuit breaker no larger than 60 VDC, 15A U.S. is used on all current-carrying

 

 

conductors. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance

 

 

and Safety Information document that accompanied this device.

 

 

 

If you ordered the universal gateway with a DC-input power supply, follow the directions in this section for proper wiring.

Note The Cisco AS5350 redundant power supply is supported in Cisco IOS Release 12.2{2)XB5 or later releases.

Caution In a DC power supply installation, do not connect the 48 VDC Return to chassis ground at the universal gateway. A single-point ground is recommended at the power distribution rack.

Note This product is intended for installation in restricted access areas and is approved for connection using 12 or 14 AWG copper conductors only. The installation must comply with all applicable codes.

27

Image 27
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways User Documentation Documents, Equipment, and ToolsRelated Hardware Documentation Cisco IOS Software DocumentationInstall Chassis Safety InformationItems Not Included Rack-Mounting the Chassis Setting Up the ChassisRequired Tools and Equipment Attaching BracketsInstallation in a Rack Desktop InstallationChassis Ground Connection Install Modules Installing Carrier CardsInstalling a Carrier Card Install the Carrier Card in the Cisco AS5350 Gateway Software Configuration Guide Installing DFCsInstalling a DFC in a Cisco AS5350 State Description DFC LEDT3 DFC Activity ACT Connect CablesColor or Port or Connection Type Connected to Cable System Management and Power ConnectionsWAN, LAN, and Voice Connections Connect a Console TerminalConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Device Connect to a WANConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Information document that accompanied this device Connecting Serial Port on Cisco AS5400 to CSU/DSUConnecting Alarm Device to Cisco AS5350 Alarm Pinouts Connect AC PowerThat accompanied this device Connect DC PowerRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a host name for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using CLI Manual ConfigurationGatewayconfig# service timestamps log datetime msec Gatewayconfig# enable secret guessmeGatewayconfig# service password-encryption Gatewayconfig# service timestamps debug datetime msecConfiguring Local AAA Security Gateway# configure terminalGateway# show privilege Configure Basic Dial Access Configuring the Asynchronous Group Interface Gatewayconfig# interface group-asyncGateway# ping Gateway# show async status Gateway# show interface async 4/0Configuring a Channelized T1 or E1 DFC Gateway# show controller t1 1/7 Configuring a Channelized T3 DFCGateway# show controller t3 1/0 Configuring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Gateway# show isdn service Gateway# show running-configGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig# interface serial 1/023 Gatewayconfig-if#ip address 172.16.254.254Gatewayconfig-if#isdn incoming-voice modem Gateway# show interface serial 1/023 Configuring the Universal Port Dial Feature Card and LinesSPE Firmware Feature DescriptionAllow all protocols to be used when connecting to the line Gateway# show line Configure ClockingDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 3 free Gatewayconfig# dial-tdm-clock priority 1 externalGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019YES Prerequisites Saving Configuration ChangesGateway# copy running-config startup-config Voice over IPConfiguration Tasks Where to Go NextSlot Numbering For new features associated with a software releaseObtaining Technical Assistance Cisco TAC Escalation Center Cisco TAC WebsiteObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.