Cisco Systems Cisco AS5350, Cisco AS5400 Initial Configuration Using CLI Manual Configuration

Page 35

Operate in full-duplex mode? [no]:

Operate at 100 Mbps speed? [yes]:

Configure IP on this interface? [yes]:

IP address for this interface [X.X.X.X]: 172.22.50.10

Subnet mask for this interface [255.255.0.0] : 255.255.255.128

Class B network is 172.22.0.0, 25 subnet bits; mask is /25

Do you want to configure FastEthernet0/0 interface? [yes]: no

Step 14 Configure your serial interfaces by responding to the following prompts:

Do you want to configure Serial0/0 interface? [no]: yes

Configure IP on this interface? [no]: yes

Configure IP unnumbered on this interface? [no]:

IP address for this interface interface: 172.22.50.11

Subnet mask for this interface: 255.255.0.0

Do you want to configure Serial0/1 interface? [yes]: no

Configuring interface Group-Async1:

Step 15 After you complete the configuration script, the setup script displays the configuration command script. Review your new configuration and then make the appropriate selection below:

[0]Go to the IOS command prompt without saving this config.

[1]Return back to the setup without saving this config.

[2]Save this configuration to nvram and exit.

Enter your selection [2]:

Initial Configuration Using CLI (Manual Configuration)

This section shows how to perform basic configuration using the command line interface (CLI).

Step 1 To proceed with manual configuration using CLI, enter no.

Would you like to enter the initial configuration dialog? [yes/no]: no

Step 2 To terminate autoinstall and continue with manual configuration, press Return:

Would you like to terminate autoinstall? [yes] Return

Step 3 To bring up the Router> prompt, press Return:

...

Router>

Step 4 Enter privileged EXEC mode.

Router> enable

Router#

Step 5 Enter global configuration mode. You are in global configuration mode when the prompt changes to Router(config)#.

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#

Step 6 Changes the name of the gateway to a meaningful name:

Router(config)# hostname Gateway

Gateway(config)#

35

Image 35
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways User Documentation Documents, Equipment, and ToolsRelated Hardware Documentation Cisco IOS Software DocumentationItems Not Included Install ChassisSafety Information Rack-Mounting the Chassis Setting Up the ChassisRequired Tools and Equipment Attaching BracketsInstallation in a Rack Desktop InstallationChassis Ground Connection Installing a Carrier Card Install ModulesInstalling Carrier Cards Install the Carrier Card in the Cisco AS5350 Gateway Software Configuration Guide Installing DFCsInstalling a DFC in a Cisco AS5350 State Description DFC LEDT3 DFC Activity ACT Connect CablesColor or Port or Connection Type Connected to Cable System Management and Power ConnectionsWAN, LAN, and Voice Connections Connect a Console TerminalConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Device Connect to a WANConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Information document that accompanied this device Connecting Serial Port on Cisco AS5400 to CSU/DSUConnecting Alarm Device to Cisco AS5350 Alarm Pinouts Connect AC PowerThat accompanied this device Connect DC PowerRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a host name for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using CLI Manual ConfigurationGatewayconfig# service timestamps log datetime msec Gatewayconfig# enable secret guessmeGatewayconfig# service password-encryption Gatewayconfig# service timestamps debug datetime msecGateway# show privilege Configuring Local AAA SecurityGateway# configure terminal Configure Basic Dial Access Gateway# ping Configuring the Asynchronous Group InterfaceGatewayconfig# interface group-async Gateway# show async status Gateway# show interface async 4/0Configuring a Channelized T1 or E1 DFC Gateway# show controller t1 1/7 Configuring a Channelized T3 DFCGateway# show controller t3 1/0 Configuring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Gateway# show isdn status Gateway# show isdn serviceGateway# show running-config Configuring the D Channels for Isdn Signaling Gatewayconfig-if#isdn incoming-voice modem Gatewayconfig# interface serial 1/023Gatewayconfig-if#ip address 172.16.254.254 Gateway# show interface serial 1/023 Configuring the Universal Port Dial Feature Card and LinesSPE Firmware Feature DescriptionAllow all protocols to be used when connecting to the line Gateway# show line Configure ClockingDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 3 free Gatewayconfig# dial-tdm-clock priority 1 externalGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019YES Prerequisites Saving Configuration ChangesGateway# copy running-config startup-config Voice over IPConfiguration Tasks Where to Go NextSlot Numbering For new features associated with a software releaseObtaining Technical Assistance Cisco TAC Escalation Center Cisco TAC WebsiteObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.