Cisco Systems Cisco AS5400 quick start Configuring the Universal Port Dial Feature Card and Lines

Page 50

Step 6 Return to privileged EXEC mode:

Gateway(config-if)# ctrl-z

Gateway#

Tip To save the gateway configuration, save it to NVRAM. Refer to the “Saving Configuration Changes” section on page 57.

Verify

To verify your D channel configuration:

Enter the show interface serial command and make sure that the line protocol is up and that you are using the correct IP interface. Also, make sure that excessive errors are not being reported.

Gateway# show interface serial 1/0:23

Serial1/0:23 is up, line protocol is up (spoofing) Hardware is DSX1

Internet address is 172.16.254.254/16

MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255

Encapsulation PPP, loopback not set

Last input 00:00:03, output never, output hang never Last clearing of "show interface" counters 00:00:01 Queueing strategy:fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops 1 minute input rate 0 bits/sec, 0 packets/sec

1 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Timeslot(s) Used:24, Transmitter delay is 0 flags

Configuring the Universal Port Dial Feature Card and Lines

Rather than the more traditional line/modem one-to-one correspondence, lines are mapped to a service process element (SPE) that resides on the universal port DFC. Associated SPE firmware serves a function similar to modem code on a MICA modem.

One SPE provides services for six ports, with additional ports per SPE. Busyout and shutdown can be configured at the SPE or port level.

The universal port DFC performs the following functions:

Converts pulse code modulation (PCM) bitstreams to digital packet data.

Forwards converted and packetized data to the main processor, which examines the data and forwards it to the backhaul egress interface.

Supports all modem standards (such as V.34 and V.42bis) and features, including dial-in and dial-out.

Note For detailed information about the universal port DFC CLI commands, refer to Monitoring Voice and Fax Services on the Cisco AS5350 and Cisco AS5400 Universal Gateway, available online at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121limit/121x/121xm/121xm_5/ftupspe. htm

50

Image 50
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways Documents, Equipment, and Tools User DocumentationCisco IOS Software Documentation Related Hardware DocumentationItems Not Included Install ChassisSafety Information Setting Up the Chassis Rack-Mounting the ChassisAttaching Brackets Required Tools and EquipmentDesktop Installation Installation in a RackChassis Ground Connection Installing a Carrier Card Install ModulesInstalling Carrier Cards Install the Carrier Card in the Cisco AS5350 Installing DFCs Gateway Software Configuration GuideInstalling a DFC in a Cisco AS5350 DFC LED State DescriptionConnect Cables T3 DFC Activity ACTConnect a Console Terminal System Management and Power ConnectionsWAN, LAN, and Voice Connections Color or Port or Connection Type Connected to CableConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Connect to a WAN DeviceConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Connecting Serial Port on Cisco AS5400 to CSU/DSU Information document that accompanied this deviceConnecting Alarm Device to Cisco AS5350 Connect AC Power Alarm PinoutsConnect DC Power That accompanied this deviceRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a host name for the gateway Press Enter for every slot, port, and channel Initial Configuration Using CLI Manual Configuration Router# configure terminalGatewayconfig# service timestamps debug datetime msec Gatewayconfig# enable secret guessmeGatewayconfig# service password-encryption Gatewayconfig# service timestamps log datetime msecGateway# show privilege Configuring Local AAA SecurityGateway# configure terminal Configure Basic Dial Access Gateway# ping Configuring the Asynchronous Group InterfaceGatewayconfig# interface group-async Gateway# show interface async 4/0 Gateway# show async statusConfiguring a Channelized T1 or E1 DFC Configuring a Channelized T3 DFC Gateway# show controller t1 1/7Gateway# show controller t3 1/0 Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Gateway# show controller t1 1/0 Gateway# show isdn status Gateway# show isdn serviceGateway# show running-config Configuring the D Channels for Isdn Signaling Gatewayconfig-if#isdn incoming-voice modem Gatewayconfig# interface serial 1/023Gatewayconfig-if#ip address 172.16.254.254 Configuring the Universal Port Dial Feature Card and Lines Gateway# show interface serial 1/023Feature Description SPE FirmwareAllow all protocols to be used when connecting to the line Configure Clocking Gateway# show lineDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 1 externalGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 3 freeYES Voice over IP Saving Configuration ChangesGateway# copy running-config startup-config PrerequisitesWhere to Go Next Configuration TasksFor new features associated with a software release Slot NumberingObtaining Technical Assistance Cisco TAC Website Cisco TAC Escalation CenterObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.