Cisco Systems Cisco AS5400 quick start Allow all protocols to be used when connecting to the line

Page 52

Step 2 Enter global configuration mode. You are in global configuration mode when the prompt changes to Gateway(config)#.

Gateway# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Gateway(config)#

Step 3 Specify the country to set the DFC parameters (including country code and encoding). This setting is applied at the system level. All DFCs use the same country code. The default is usa if the gateway is configured with T1 interfaces and e1-defaultif the gateway is configured with E1 interfaces. Use the no form of this command to set the country code to the default of domestic.

Note All sessions on all DFCs in all slots must be idle for this command to run.

Gateway(config)# spe country country name

Step 4 Enter the numbers of the ports to configure. If you want to configure 108 ports on slot 3, enter line 3/00 3/107. If you want to configure 324 ports on slots 3-5, enter line 3/00 5/107.

Gateway(config)# line slot/port slot/port

Gateway(config-line)#

Step 5 Allow all protocols to be used when connecting to the line:

Gateway(config-line)# transport input all

Step 6 Enable remote IP users running a PPP application to dial in, bypass the EXEC facility, and connect directly to the network:

Gateway(config-line)# autoselect ppp

Step 7 Enable incoming and outgoing calls:

Gateway(config-line)# modem inout

Step 8 Return to privileged EXEC mode:

Gateway(config-line)# Ctrl-Z

Gateway#

Tip To save the gateway configuration, save it to NVRAM. Refer to the “Saving Configuration Changes” section on page 57.

Verify

To verify your SPE configuration:

To display a summary for all the lines, enter the show spe command:

Gateway# show spe

SPE settings:

==============

Country code configuration: default T1 (u Law)

Polling interval: 8 secs.

History log events: 50(per port) Port legends:

============

Port state: (s)shutdown (t)test (r)recovery (d)download (b)busiedout (p)busyout pending, (B)bad (a)active call

Call type: (m)modem (d)digital (f)fax-relay (v)voice (_)not in use System resources summary:

======================

52

Image 52
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways Documents, Equipment, and Tools User DocumentationCisco IOS Software Documentation Related Hardware DocumentationSafety Information Install ChassisItems Not Included Setting Up the Chassis Rack-Mounting the ChassisAttaching Brackets Required Tools and EquipmentDesktop Installation Installation in a RackChassis Ground Connection Installing Carrier Cards Install ModulesInstalling a Carrier Card Install the Carrier Card in the Cisco AS5350 Installing DFCs Gateway Software Configuration GuideInstalling a DFC in a Cisco AS5350 DFC LED State DescriptionConnect Cables T3 DFC Activity ACTSystem Management and Power Connections WAN, LAN, and Voice ConnectionsConnect a Console Terminal Color or Port or Connection Type Connected to CableConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Connect to a WAN DeviceConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Connecting Serial Port on Cisco AS5400 to CSU/DSU Information document that accompanied this deviceConnecting Alarm Device to Cisco AS5350 Connect AC Power Alarm PinoutsConnect DC Power That accompanied this deviceRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Power Up the Universal Gateway Checklist for Power UpPower-Up Procedure Perform Initial Configuration Initial Configuration Using the Setup Command FacilityEnter a host name for the gateway Press Enter for every slot, port, and channel Initial Configuration Using CLI Manual Configuration Router# configure terminalGatewayconfig# enable secret guessme Gatewayconfig# service password-encryptionGatewayconfig# service timestamps debug datetime msec Gatewayconfig# service timestamps log datetime msecGateway# configure terminal Configuring Local AAA SecurityGateway# show privilege Configure Basic Dial Access Gatewayconfig# interface group-async Configuring the Asynchronous Group InterfaceGateway# ping Gateway# show interface async 4/0 Gateway# show async statusConfiguring a Channelized T1 or E1 DFC Configuring a Channelized T3 DFC Gateway# show controller t1 1/7Gateway# show controller t3 1/0 Configuring Isdn PRI Area Keyword Switch Type Gatewayconfig# controller t3 7/016Gateway# show controller t1 1/0 Gateway# show running-config Gateway# show isdn serviceGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig-if#ip address 172.16.254.254 Gatewayconfig# interface serial 1/023Gatewayconfig-if#isdn incoming-voice modem Configuring the Universal Port Dial Feature Card and Lines Gateway# show interface serial 1/023Feature Description SPE FirmwareAllow all protocols to be used when connecting to the line Configure Clocking Gateway# show lineDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 1 external Gatewayconfig# dial-tdm-clock priority 2 4/6Gatewayconfig# dial-tdm-clock priority 2 1/019 Gatewayconfig# dial-tdm-clock priority 3 freeYES Saving Configuration Changes Gateway# copy running-config startup-configVoice over IP PrerequisitesWhere to Go Next Configuration TasksFor new features associated with a software release Slot NumberingObtaining Technical Assistance Cisco TAC Website Cisco TAC Escalation CenterObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.