Cisco Systems Cisco AS5350, Cisco AS5400 quick start Power-Up Procedure

Page 31

Power-Up Procedure

Perform this procedure to power up your Cisco universal gateway and verify that it goes through its initialization and self-test. When this is finished, the Cisco universal gateway is ready to configure.

Note To view the boot sequence through a terminal session, you must have a console connection to the Cisco universal gateway before it powers on. To connect to the console, refer to the “Connect a Console Terminal” section on page 15.

Move the power switch to the ON position. The system board OK LED should come on and messages will begin to appear in your terminal emulation program window.

Caution Do not press any keys on the keyboard until the messages stop. Any keys pressed during this time are interpreted as the first command typed when the messages stop, which might cause the universal gateway to power off and start over. It takes a few minutes for the messages to stop.

Note The displayed messages depend on the Cisco IOS software release and cards installed in your system. The screen displays in this section are for reference only and might not exactly reflect the messages on your console.

The messages look similar to the following:

System Bootstrap, Version 12.1(2r)XD1, RELEASE SOFTWARE (fc1)

Copyright (c) 2000 by cisco Systems, Inc.

AS5350 platform with 131072 Kbytes of main memory

Self decompressing the image : ################################################[OK]

Self decompressing the image : ################################################[OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph

(c)of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph

(c)(1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 5350 Software (C5350-IS-M), Version 12.2(2)XA, EARLY DEPLOYMENT RELEASE

SOFTWARE (fc1)

TAC:Home:SW:IOS:Specials for info

Copyright (c) 1986-2001 by cisco Systems, Inc.

Compiled Tue 26-Jun-01 23:47 by hwcheng

Image text-base: 0x600089C8, data-base: 0x61000000

cisco AS5350 (R7K) processor (revision O) with 131072K/65536K bytes of memory. Processor board ID JAB0430086M

R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache Last reset from IOS reload

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1. Manufacture Cookie Info:

EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32, Board Hardware Version 3.27, Item Number 800-5171-01, Board Revision B0, Serial Number JAB0430086M,

31

Image 31
Contents Cisco AS5350 and Cisco AS5400 Universal Gateways User Documentation Documents, Equipment, and ToolsRelated Hardware Documentation Cisco IOS Software DocumentationSafety Information Install ChassisItems Not Included Rack-Mounting the Chassis Setting Up the ChassisRequired Tools and Equipment Attaching BracketsInstallation in a Rack Desktop InstallationChassis Ground Connection Installing Carrier Cards Install ModulesInstalling a Carrier Card Install the Carrier Card in the Cisco AS5350 Gateway Software Configuration Guide Installing DFCsInstalling a DFC in a Cisco AS5350 State Description DFC LEDT3 DFC Activity ACT Connect CablesColor or Port or Connection Type Connected to Cable System Management and Power ConnectionsWAN, LAN, and Voice Connections Connect a Console TerminalConnecting Cisco AS5350 to Console Terminal Connect to Ethernet Network Device Connect to a WANConnecting 8-Port DFC on Cisco AS5350 to RJ-45 Jack Accompanied this device RJ-45 jack E1 cable Connecting T3 DFC on Cisco AS5350 to T3 CSU/DSU Connecting T3 DFC on Cisco AS5400 to T3 CSU/DSU Information document that accompanied this device Connecting Serial Port on Cisco AS5400 to CSU/DSUConnecting Alarm Device to Cisco AS5350 Alarm Pinouts Connect AC PowerThat accompanied this device Connect DC PowerRemove power from the DC circuit Cisco AS5400 DC Power Supply Connections Checklist for Power Up Power Up the Universal GatewayPower-Up Procedure Initial Configuration Using the Setup Command Facility Perform Initial ConfigurationEnter a host name for the gateway Press Enter for every slot, port, and channel Router# configure terminal Initial Configuration Using CLI Manual ConfigurationGatewayconfig# service timestamps log datetime msec Gatewayconfig# enable secret guessmeGatewayconfig# service password-encryption Gatewayconfig# service timestamps debug datetime msecGateway# configure terminal Configuring Local AAA SecurityGateway# show privilege Configure Basic Dial Access Gatewayconfig# interface group-async Configuring the Asynchronous Group InterfaceGateway# ping Gateway# show async status Gateway# show interface async 4/0Configuring a Channelized T1 or E1 DFC Gateway# show controller t1 1/7 Configuring a Channelized T3 DFCGateway# show controller t3 1/0 Configuring Isdn PRI Gatewayconfig# controller t3 7/016 Area Keyword Switch TypeGateway# show controller t1 1/0 Gateway# show running-config Gateway# show isdn serviceGateway# show isdn status Configuring the D Channels for Isdn Signaling Gatewayconfig-if#ip address 172.16.254.254 Gatewayconfig# interface serial 1/023Gatewayconfig-if#isdn incoming-voice modem Gateway# show interface serial 1/023 Configuring the Universal Port Dial Feature Card and LinesSPE Firmware Feature DescriptionAllow all protocols to be used when connecting to the line Gateway# show line Configure ClockingDial Feature Card Ports Gatewayconfig# dial-tdm-clock priority 3 free Gatewayconfig# dial-tdm-clock priority 1 externalGatewayconfig# dial-tdm-clock priority 2 4/6 Gatewayconfig# dial-tdm-clock priority 2 1/019YES Prerequisites Saving Configuration ChangesGateway# copy running-config startup-config Voice over IPConfiguration Tasks Where to Go NextSlot Numbering For new features associated with a software releaseObtaining Technical Assistance Cisco TAC Escalation Center Cisco TAC WebsiteObtaining Additional Publications and Information Page USA

Cisco AS5400, Cisco AS5350 specifications

Cisco Systems is a global leader in networking and telecommunications technology, and its AS5350 and AS5400 models are prominent offerings in their product line. These devices cater primarily to service providers and large enterprises looking for advanced VoIP, data, and multimedia capabilities.

The Cisco AS5350 is a versatile voice gateway that supports a wide range of protocols including VoIP and PSTN (Public Switched Telephone Network). Designed for scalability, it can handle numerous simultaneous calls, making it an ideal solution for businesses that require robust communication systems. Some of its main features include built-in support for various signaling protocols such as SIP (Session Initiation Protocol) and H.323, which allow seamless integration with existing networks. Additionally, the AS5350 is equipped with high-density digital signal processors (DSPs) that enable efficient call processing and transcoding, ensuring high-quality voice transmission.

On the other hand, the Cisco AS5400 takes this functionality a step further by offering enhanced capabilities suited for more demanding environments. It supports both voice and data services, allowing service providers to deliver a comprehensive solution that includes voice calls, multimedia applications, and broadband services. The AS5400 features a modular design, allowing users to adapt the device to specific needs by adding or removing modules as required. This modularity enhances flexibility and future-proofs the system against evolving technology demands.

Both the AS5350 and AS5400 incorporate advanced security features to protect sensitive communications and data. Features such as encryption, secure signaling, and network access controls are essential for enterprises looking to safeguard their operations in an increasingly vulnerable digital landscape. These gateways also support Quality of Service (QoS) protocols, ensuring that voice traffic is prioritized over other types of data, thereby maintaining call clarity even in times of high data demand.

In conclusion, the Cisco AS5350 and AS5400 are compelling solutions that showcase Cisco's commitment to delivering reliable and high-performance telecommunications devices. By offering state-of-the-art technology, robust features, and a modular approach to scalability, businesses and service providers can ensure they remain competitive in the ever-evolving telecommunications landscape. Whether it is for voice, data, or multimedia applications, these gateways deliver the performance and flexibility needed to meet current and future challenges.