Cisco Systems 4490 manual Line Conditioners, Uninterruptible Power Supplies

Page 76

Chapter 5 Maintaining the Cisco Global Site Selector 4490

Using Power Protection Devices

Line Conditioners

Line conditioners go beyond the overvoltage protection of surge protectors. Line conditioners keep a system’s AC power source voltage at a fairly constant level and therefore can handle brownouts. Because of this added protection, line conditioners cost more than surge protectors—up to several hundred dollars. However, these devices cannot protect against a complete loss of power.

Uninterruptible Power Supplies

Uninterruptible power supply (UPS) systems offer the most complete protection against variations in power because they use battery power to keep the system running when AC power is lost. The battery is charged by the AC power while it is available, so once AC power is lost, the battery can provide power to the system for a limited amount of time—from 15 minutes to an hour or so—depending on the UPS system.

Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters Laboratories (UL) safety-approved.

 

Cisco Global Site Selector 4490 Hardware Installation Guide

5-8

78-15755-02

Image 76
Contents Cisco Global Site Selector 4490 Hardware Installation Guide Page Cisco Global Site Selector 4490 Hardware Installation Guide Page N T E N T S Checking Connections Altitude Viii Figure B-1 Page Table A-1 Xii Preface Audience How to Use This Guide Chapter/Appendix DescriptionRelated Documentation Document Title ProvidesSymbols and Conventions XviiBewaar Deze Instructies Varoitus Tärkeitä TurvallisuusohjeitaWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaTA Vare PÅ Disse Instruksjonene Aviso Instruções Importantes DE SegurançaVarning! Viktiga Säkerhetsanvisningar Spara Dessa AnvisningarXxii Introduction IntroductionSystem Hardware Features Cisco Global Site Selector 4490-Front View Hardware Features Front Panel Control ButtonsLED Indicators Front Panel LEDsColor 5shows the location of back panel LEDs, and -3describesInput/Output Ports and Connectors Indicator Color State DescriptionGlobal Site Selector 4490 Back Panel Ports and Receptacles Ethernet Port Pin Number Signal Name RI Ring IndicatorParameters Settings VT100/ANSIChapter Preparing for Installation Safety Warnings Site Requirements Safety GuidelinesSafety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Preparing for Installation Safety Warnings Choosing a Site for Installation Site RequirementsEnsuring Overcurrent Protection Grounding the GSSSafety Guidelines General PrecautionsPreparing for Installation Safety Guidelines Protecting Against Electrostatic Discharge Rack Installation Safety Guidelines Ensuring Proper AirflowStabilizing the System Lifting the SystemPreparing for Installation Safety Guidelines Installing the Cisco Global Site Selector Unpacking and Inspecting the Global Site Selector Tools and Parts Required If the Product is DamagedFour-Post Rack Installation Kit Installing Your Unit Installing the Chassis in a Four-Post Rack Cage nuts Clip nutsRemoving the Inner Slide Rail Attaching the Inner Slide Rail to the GSS Attaching the Slide Rails to the Rack Inserting the Inner Slide Rails Installing the Chassis in a Two-Post Rack Attaching a Bracket to the Right Side of the GSSAttaching the GSS 4490 to the Two-Post Rack Installing the Chassis on a Workbench or Tabletop Connecting Cables Connecting Power Booting the SystemChecking the Front Panel LEDs Color State DescriptionRemoving or Replacing a Cisco Global Site Selector Cisco Global Site Selector 4490 Hardware Installation Guide Troubleshooting the System Hardware Checking the BasicsTroubleshooting the System Hardware Checking the Basics Checking Connections Troubleshooting the System Hardware Checking Connections Maintaining the Cisco Global Site Selector Maintaining Your Site EnvironmentTemperature Humidity AltitudeCorrosion Dust and ParticlesElectrostatic Discharge Electromagnetic and Radio Frequency Interference Power Source Interruptions MagnetismUsing Power Protection Devices Surge ProtectorsUninterruptible Power Supplies Line ConditionersSpecifications Specification DescriptionAppendix a Specifications Connecting a Modem to the GSS 4490 Console Port Configuring a Modem Cabling a Modem to the GSSConfiguring a Modem Figure B-1 Console Port ConnectorCabling a Modem to the GSS Parameters Default Settings Regulatory Compliance and EMI Class a Warnings Regulatory Compliance EMI Class a Warning StatementsRegulatory Compliance EMCEMI Class a Warning Statements FCC Class a Warning Canada Class a WarningCispr 22 Class a Warning Vcci Class a Notice for Japan User may be requested to take appropriate countermeasuresHungary Class a Warning 78-15755-02 D E IN-2 IN-3 IN-4
Related manuals
Manual 20 pages 33.28 Kb Manual 94 pages 36.36 Kb