Cisco Systems BC-109 manual Configuring Source-Route Bridging, SRB Configuration Task List

Page 1

Configuring Source-Route Bridging

This chapter describes source-route bridging (SRB) configuration tasks. For a discussion of remote source-route bridging (RSRB) configuration tasks, refer to the “Configuring Remote Source-Route Bridging” chapter in this publication.

For a complete description of the SRB commands mentioned in this chapter, refer to the “Source-Route Bridging Commands” chapter in the Bridging and IBM Networking Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index or search online.

SRB Configuration Task List

Perform the tasks in the following sections to configure SRB:

•

•

•

•

•

•

•

•

•

Configure Source-Route Bridging

Configure Bridging of Routed Protocols

Configure Translation between SRB and Transparent Bridging Environments

Configure NetBIOS Support

Configure LNM Support

Secure the SRB Network

Tune the SRB Network

Establish SRB Interoperability with Specific Token Ring Implementations

Monitor and Maintain the SRB Network

See the end of this chapter for “SRB Configuration Examples.”

Warning The Cisco IOS software issues a warning if a duplicate bridge definition exists in a router. You must remove an old bridge definition before adding a new bridge definition to a router configuration.

Configuring Source-Route Bridging BC-109

Image 1

Contents SRB Configuration Task List Configuring Source-Route BridgingConfigure a Dual-Port Bridge Configure Source-Route BridgingMultiple Dual-Port Bridges Configure a Multiport Bridge Using a Virtual RingSource-bridge ring-group ring-group Define a Ring Group in SRB ContextNo source-bridge ring-group ring-group Enable SRB and Assign a Ring Group to an Interface Configure SRB over FddiInterface fddi slot/port Source-bridge route-cache cbusConfigure SRB over Frame Relay Configure Fast-Switching SRB over FddiEnable the Automatic Spanning-Tree Function Limit the Maximum SRB Hops Enable Use of the RIF Configure Bridging of Routed ProtocolsConfigure the RIF Timeout Interval Configure a Static RIF EntryOverview of SR/TLB Following notes and caveats apply to all uses of SR/TLB Disable Fast-Switched SR/TLB Enable Bridging between Transparent Bridging and SRBEnable Translation Compatibility with IBM 8209 Bridges No source-bridge transparent ring-group fastswitchEnable 0x80d5 Processing Enable Token Ring LLC2-to-Ethernet ConversionEnable Standard Token Ring LLC2-to-Ethernet LLC2 Conversion Source-bridge sap-80d5 dsapConfigure NetBIOS Support Source-bridge proxy-netbios-only Specify Timeout and Enable NetBIOS Name CachingEnable NetBIOS Proxying Configure the NetBIOS Cache Name LengthCreate Static Entries in the NetBIOS Name Cache Specify Dead-Time Intervals for NetBIOS PacketsNetbios name-cache query-timeout seconds Configure LNM SupportNetbios name-cache recognized-timeout seconds LNM Linking to a Source-Route Bridge on Each Local Ring LAN Network Manager Monitoring and Translating How a Router Works with LNMDisable LNM Functionality Enable Other LRMs to Change Router Parameters Disable Automatic Report Path Trace FunctionEnable LNM Servers Apply a Password to an LNM Reporting LinkChange Reporting Thresholds Monitor LNM Operation Change an LNM Reporting IntervalLnm softerr milliseconds Configure NetBIOS Access Filters Using Station Names Configure NetBIOS Access FiltersSecure the SRB Network Netbios access-list host name permit deny pattern Configure NetBIOS Access Filters Using a Byte OffsetNetbios access-list bytes name permit deny offset Netbios input-access-filter bytes nameNetbios output-access-filter bytes name Configure Administrative Filters for Token Ring TrafficFilter Frames by Protocol Type Filter Source Addresses Filter Frames by Vendor CodeFilter Destination Addresses Access Expression Example Optimize Access Expressions Configure Access ExpressionsTune the SRB Network Alter Access Lists Used in Access ExpressionsEnable or Disable the Source-Route Fast-Switching Cache Establish the Connection Timeout Interval Enable or Disable the SSEOptimize Explorer Processing Controlling Explorer Storms in Redundant Network Topologies Establish SRB Interoperability with TI MAC Firmware Configure Proxy ExplorersMac-address ieee-address Monitor and Maintain the SRB Network Report Spurious Frame-Copied ErrorsSource-bridge tcp-queue-max number SRB Configuration ExamplesBasic SRB with Spanning-Tree Explorers Example Dual-Port Source-Route Bridge ConfigurationSRB-Only Example Optimized Explorer Processing Configuration ExampleMultiport SRB Example SRB and Routing Certain Protocols ExampleSRB with Multiple Virtual Ring Groups Example Configuration for Router aSRB over Fddi Fast-Switching Example SRB over Fddi Configuration ExamplesConfiguration for Router B Router aFrad Using SRB over Frame Relay to Connect to a Cisco Router SRB over Frame Relay Configuration ExampleConfiguration on Router B Configuration of Router aConfiguration on Router C Adding a Static RIF Cache Entry ExampleSR/TLB for a Simple Network Example Adding a Static RIF Cache Entry for a Two-Hop Path ExampleBC-154Bridging and IBM Networking Configuration Guide Example of a Bit-Swapped Address SR/TLB with Access Filtering ExampleSpecifying a Static Entry NetBIOS Support with a Static NetBIOS Cache Entry ExampleLNM for a Simple Network Example Wayfarer# show lnm configLNM for a More Complex Network Example NetBIOS Access Filters Example Filtering Bridged Token Ring Packets to IBM Machines Example Shows a router connecting four Token Rings Following access expression would result Creating Access Filters ExampleFast-Switching Example Access Filters ExampleAutonomous Switching Example