Cisco Systems 8540 CSR, 8510 CSR appendix Configuring Loopback

Page 33

Chapter 4 Configuring Interfaces

Configuring the ATM Uplink Interface (Catalyst 8540)

Configuring SONET Alarms

The ATM OC-12c and the ATM OC-3c uplink interfaces support SONET alarm monitoring. To configure alarm monitoring, perform the following steps, beginning in global configuration mode:

 

Command

Purpose

Step 1

 

 

Router(config)# interface atm

Enters interface configuration mode and specifies the ATM

 

slot/subslot/interface

interface to configure.

 

Router(config-if)#

 

Step 2

 

 

Router(config-if)# sonet report

Permits console logging of selected SONET alarms.

 

{b1-tca b2-tca b3-tca lais

The alarms are as follows:

 

lrdi pais plm-p plop prdi

 

• b1-tca(B1 bit error rate [BER] threshold crossing alarm)

 

rdool sd-ber sf-ber slof slos

 

tim-p uneq-p}

• b2-tca(B2 BER threshold crossing alarm)

 

 

 

 

• b3-tca(B3 BER threshold crossing alarm)

 

 

• lais (line alarm indication signal)

 

 

• lrdi (line remote defect indication)

 

 

• pais (path alarm indication signal)

 

 

• plm-p(payload label, C2 mismatch alarm)

 

 

• plop (path loss of pointer), prdi (path remote defect

 

 

indication)

 

 

• rdool (receive data out of lock)

 

 

• sd-ber(LBIP BER in excess of threshold)

 

 

• sf-ber(signal failure BER)

 

 

• slof (section loss of frame)

 

 

• slos (section loss of signal)

 

 

• tim-p(path trace identifier, J1 mismatch alarm)

 

 

• uneq-p(path unequipped C2 alarm).

 

 

The b1-tca,b2-tca,b3-tca,plop, sf-ber,slof, slos are enabled by

 

 

default.

Step 3

 

 

Router(config-if)# sonet

Sets the BER threshold values of the specified alarms. Default

 

threshold {b1-tca b2-tca

values are 6 for b1-tca, b2-tca, b3-tca, and sd-ber; 3 for sf-ber.

 

b3-tca sd-ber sf-ber}rate

 

 

 

 

To determine which alarms are reported on the ATM interface, and to display the BER thresholds, use the show controllers atm command, as described in the “Verifying the ATM Configuration” section on page 4-36.For a detailed description of the sonet report and sonet threshold commands, refer to the ATM Switch Router Command Reference publication.

Configuring Loopback

The ATM uplink interface is configured by default with no loopback. To enable loopback, use the loopback command in interface configuration mode.

 

 

Layer 3 Switching Software Feature and Configuration Guide

 

 

 

 

 

 

 

78-6235-04, Cisco IOS Release 12.0(10)W5(18)

 

 

4-33

 

 

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Configuring Interfaces Overview of Interface Configuration Media Access Control AddressInterface Port Identifier General Instructions for Configuring Interfaces Router# configure terminalRouterconfig# interface gigabitethernet 1/0/1 About Layer 3 Switching Interfaces Command Purpose Initially Configuring Gigabit Ethernet InterfacesAbout the Enhanced Gigabit Ethernet Interfaces Catalyst ExampleInitially Configuring Fast Ethernet Interfaces Verifying the Ethernet Interface ConfigurationCommand Description Examples Router# show interface gigabitethernet 0/0/0Router# show interface fastethernet 1/0/0 About Virtual LANs Configuring ISL Vlan EncapsulationRouterconfig-subif# Enters subinterface configuration modeConfigure the Fast Ethernet main interface Routerconfig-if# Routerconfig# bridge bridge-group protocol ieeeRouterconfig# interface fastethernet 1/0/1.1 Configuring 802.1Q Vlan EncapsulationRouterconfig-subif#interface fastethernet 1/0/0 Routerconfig-subif#interface fastethernet 3/0/1Ieee Bridge-groupAbout Packet over Sonet Catalyst Monitoring Vlan OperationPOS About the POS OC-12c Uplink InterfaceConfiguring the POS OC-12c Uplink Interface Catalyst Default Configuration Initially Configuring the POS InterfaceParameter Configuration Command Default Value Ip-address subnet-mask Automatic Reverting of Clock SourceHdlc ppp Line internalCustomizing the Configuration Additional ConfigurationsSetting the MTU Size Configuring Sonet Overhead Configuring FramingSdh sonet Value j0 value sls0 valueConfiguring POS SPE Scrambling Scrambling is on by defaultScramble-atm Configuring Sonet Alarms Configuring Sonet Delay Triggers AlarmAlarm Description Lais pais plop prdi slof Verifying the POS ConfigurationSlos Triggers line path millisecondRouter# show protocols pos 1/0/0 LOP = PLM-P Router# show controllers pos 2/0/0Router# show controller pos 2/0/0 detail Smdr About the ATM Uplink Interface About ATM Uplinks CatalystConfiguration Overview Configuring the ATM Uplink Interface CatalystNo loopback No atm sonet stm-1 for OC-3No atm clock internal Initially Configuring the ATM Uplink InterfaceAtm vc-per-vp Parameter ValueConfiguring the Clock Source Routerconfig-if# atm sonet Configuring Sonet FramingStm-1 ATM interface or to STM-4 for the OC-12c interfaceMsg line j1 16byte exp-msg Overhead c2 byte j0 bytesSls0 is part of the payload pointer byte Line msg line 64byte exp-msgConfiguring Loopback Configuring CDP Configuring Virtual CircuitsConfiguring the Maximum VCs per VP Creating a PVCVpi vci aal-encap Mapping a Protocol Address to a PVCIp-address atm-vc vcd NameVerifying the ATM Configuration Switch Router aSwitch Router B 5CB About Port Snooping Configuring Interfaces About Port SnoopingRestrictions on Port Snooping Configuring SnoopingAbout the Snooping Destination Port About the Snooping Source PortSource-port Direction receive transmit bothShow snoop interface Monitoring SnoopingDestination-port Show snoop78-6235-04, Cisco IOS Release 12.010W518
Top Page Image Contents