Cisco Systems 350, 340 manual Troubleshooting Resetting to the Default Configuration

Page 50

Chapter 4 Troubleshooting

Resetting to the Default Configuration

Step 9 Write down the list of files for future reference.

Caution Perform the next six steps carefully to avoid accidently deleting the installation key files or the firmware files. You must carefully note the file selection letters, because they change during the following steps. If you forget to copy the access point’s installation key file to DRAM in Step 10, or if you do not copy it back to configuration memory in Step 13, your access point will stop functioning.

Step 10 Copy the access point’s AP Installation Key to the access point’s DRAM by pressing c to select Copy file, then 1 to select DRAM, then the selection letter for the file AP Installation Key.

Step 11 If the list of configuration files contains a file called VAR Installation Key, you must copy that file to DRAM along with the AP Installation Key file. If the access point does not have a VAR installation key file, skip to Step 12.

Caution If you forget to copy the access point’s VAR installation key file to DRAM in Step 11, or if you do not copy it back to configuration memory in Step 14, your access point will stop functioning.

Copy the VAR Installation Key to DRAM by pressing c to select Copy file, then 1 to select DRAM, then the selection letter for the file VAR Installation Key.

Step 12 Reformat the access point’s configuration memory bank by pressing Ctrl-Zto reach the reformat menu. When the menu appears, press ! to select FORMAT memory bank, then 2 to select Config, then upper-case Y to confirm the FORMAT command.

Caution Make sure you select the Configuration memory bank for formatting. If you accidentally format a different memory bank your access point will stop functioning.

Step 13 Copy the installation key back to the configuration memory bank by pressing c to select Copy file, then 2 to select Config, then the selection letter for the file AP Installation Key.

Step 14 If you copied a VAR installation key to DRAM in Step 11, copy it back to the configuration memory bank by pressing c to select Copy file, then 2 to select Config, then the selection letter for the file VAR Installation Key. If the access point does not have a VAR installation key file, skip to Step 15.

Step 15 Run the access point firmware by pressing r to select Run, then the selection letter for the firmware file that is displayed. The message “Inflating [firmware file name]” appears while the access point starts the firmware.

Step 16 When the Express Setup screen appears, begin reconfiguring the access point using the terminal emulator or an Internet browser.

Cisco Aironet Access Point Hardware Installation Guide

4-8

OL-0738-02

 

 

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Cisco Aironet Access Point Hardware Installation Guide Cisco Aironet Access Point Hardware Installation Guide N T E N T S Using an Internet Browser Installation Warning A-3 OL-0738-02 Organization ObjectivesAudience Conventions Related PublicationsCisco.com Obtaining DocumentationDocumentation Feedback Ordering DocumentationOpening a TAC Case Obtaining Technical AssistanceCisco TAC Website TAC Case Priority DefinitionsObtaining Additional Publications and Information Xii Overview Omni-Directional Antennas Key FeaturesInline Power Ethernet and Serial Ports Metal EnclosureIndicators Ethernet Status RadioNetwork Configuration Examples Root Unit on a Wired LANRepeater Unit That Extends Wireless Range Access Point Root Unit Wired LAN Access Point RepeaterCentral Unit in an All-Wireless Network Access Point Root UnitAccess Point Specifications Category SpecificationAccess Point Specifications OL-0738-02 Installation Installation Special Considerations Installation GuidelinesBasic Guidelines Coverage OptionsMinimal Overlap Coverage Option Heavy Overlap Coverage Option Unpacking the Access Point Package ContentsConnecting the Ethernet and Power Cables Connecting Cables on 340 Series Access PointsConnecting Cables on 350 Series Access Points Access Point Power OptionsInstallation Connecting the Ethernet and Power Cables OL-0738-02 Basic Configuration Before You Start Summary of Configuration StepsUsing the IP Setup Utility Obtaining and Installing Ipsu Finding the Access Point’s IP AddressSetting the Access Point’s IP Address and Ssid Click Set ParametersEntering Basic Settings Using an Internet BrowserBasic Configuration Entering Basic Settings Using a Terminal Emulator Selecting Pages and SettingsSerial Basic Configuration Entering Basic Settings Default Basic Settings Setting Name Default ValueTroubleshooting Checking the Top Panel Indicators Indicators on the 340 Series and 350 Series Access PointChecking Basic Settings WEP KeysResetting to the Default Configuration Steps for Firmware Versions 11.07 or Later Determining the Boot-Block Version Steps for Firmware Versions 11.06 or EarlierReconfiguration Steps for Boot Block Version 1.01 or Earlier Reconfiguration Steps for Boot Block Version 1.02 or Later Troubleshooting Resetting to the Default Configuration Translated Safety Warnings Explosive Device Proximity Warning Modifierats för att kunna användas i sådana sammanhangInstallation Warning Lightning Activity WarningCircuit Breaker 15A Warning Page Power Injector Warning Appendix a Translated Safety Warnings Power Injector Warning OL-0738-02 Declarations of Conformity and Regulatory Information For Home or Office USE Department of Communications Canada Canadian Compliance StatementCisco Aironet Access Point Hardware Installation Guide Declaration of Conformity for RF Exposure Japanese Translation Declaration of Conformity Statements OL-0738-02 D E IN-2 IN-3 IN-4
Related manuals
Manual 6 pages 18.88 Kb Manual 15 pages 37.54 Kb Manual 12 pages 49.99 Kb Manual 6 pages 34.97 Kb Manual 12 pages 13.14 Kb
Top Page Image Contents