Baracoda 2.9/ Prefix and suffix, 2.9.1/ Prefix/suffix, RoadRunners BRR-L Programming guide

Page 13
RoadRunners BRR-L Programming guide

RoadRunners BRR-L Programming guide

dec 2006

2.9/ Prefix and suffix

The barcode string can be added a prefix, a postprefix, a suffix and/or a postsuffix. These can come as described below:

prefix

postprefix

barcode

suffix

postsuffix

2.9.1/ Prefix/suffix

You can add a prefix and/or a suffix (strings of more than 32 characters will not be accepted) to every barcode sent to the host device.

There is no prefix/suffix in default settings.

PREFIX on

SUFFIX on

PREFIX off (*)

SUFFIX off (*)

START

Read « Set Suffix (prefix) » label

Read intermediary label

Corresponding to the next character to set for the

suffix (appendix 1 of this document)

NO

Finished * ?

YES

Read « END of config » label

END

Programming procedure for “set suffix (prefix)” option.

*= max length of the Suffix (Prefix) is 32 characters

Set prefix

End of configuration

Set suffix

© Baracoda 2006

13/29

Image 13
Contents Data Capture for RoadRunners BRR-L & BBR-LA Programming GuideWorkforce in Motion Important notice2/ GENERAL CONFIGURATION RoadRunners BRR-L & BRR-LA Programming guide Nov3/ DECODER SETTINGS RoadRunners BRR-L & BRR-LA Programming Guide3/29 1/ Introduction2.1/ Reset all parameters 2/ General Configuration2.3/ Baracoda advanced features 2.2/ Erase all barcodes in memory2.3.3/ No data loss mode and Baracoda Header Baracoda header 2.3.2/ Shutdown timersNo data loss mode 5/292.3.4/ Timestamp Option Programming procedure for “set Timestamp” option6/29 7/29 2.4/ Reading Mode2.5.1/ Real time mode 2.5/ Operating ModeREAL TIME mode REAL TIME with ACK beep and bufferisation9/29 2.5.2/ Batch mode2.6/ Cradle / RS232 jack 2.6.1/ Cradle 2.7/ Buzzer and Led Settings2.6.2/ RS232 jack Parameters are11/29 2.8/ Bluetooth commands 2.8.1/ Bluetooth name2.8.3/ Power emission settings 2.8.2/ Sniff settings2.8.4/ Security code PIN settings 12/292.9.1/ Prefix/suffix 2.9/ Prefix and suffixRoadRunners BRR-L Programming guide 13/29Feature enabled for CPU firmware version ≥ 2.9.2/ Postrefix/postsuffix14/29 3.1/ Symbology default settings 3/ Decoder settings3.2/ Symbology Identifier 3.4/ Disable All Symbologies3.5/ Set decoder barcode length 3.6/ Codabar settingsRoadRunners BRR-L Programming guide Programming procedure for “set barcode length” option3.8/ Code 39 settings 3.7/ Code 11 Settings17/29 Code 39 - format - full ASCII 3.9/ Code 93 SettingsCode 39 - check digit - not used 18/293.10.2/ EAN 128 Group Separator 3.10/ Code 128 Settings 3.10.1/ General19/29 3.12/ MSI Code Settings 3.11/ Interleaved 2 of 5 Settings20/29 3.14/ UPC/ EAN Settings 3.13/ Standard 2 of 5 Settings21/29 22/29 Programming procedure for “set min Max length” option 3.15/ Set min or Max length option23/29 Interleaved 2 of Standard 2 of 5 industrial 2 of Code MSI UPC E EAN SELECT ALL Code Code 128 / EAN EAN 13 / UPC A Code CodabarSymbology table Selected SymbologyCapital letters A-Z APPENDIX 1 ASCII Table A-Z, a-z, 0-9, ponctuation, Control characters25/29 NameSmall letters a-z Ponctuation Space26/29 a b c d e f g h i j k l m27/29 Decimal numbers28/29 Control CharactersCR EOT ETX LF NUL SOH STX TABSymbology Character APPENDIXModifier Characters Code 39 Option Values