Baracoda BRR-L 3.10/ Code 128 Settings 3.10.1/ General, 3.10.2/ EAN 128 Group Separator, 19/29

Page 19

RoadRunners BRR-L Programming guide

dec 2006

3.10/ Code 128 Settings

3.10.1/ General

Code 128/EAN 128 - not active

Code 128/EAN 128 - barcode length - any length (*)

Code 128/EAN 128 – active (*)	Code 128/EAN 128 - barcode length - minimum
	length = 6

3.10.2/ EAN 128: Group Separator

‘FNC1’ included in an EAN128 code is transmitted by default as ‘GS’ (Group Separator – 0x1D). (Feature enablde for CPU firmware version > 3.00)

Enable GS transmission (*)

Disable GS transmission

It is possible to replace that ‘GS’ data to an other ASCII data. (Feature enabled for CPU firmware version > 3.00)

START

Read « define GS » label

Read intermediary label

Corresponding to the next character to set for the

replacing data of GS

Finished ?

YES

Read « END of config » label

END

Define GS

End of configuration

19/29

Image 19

Contents Important notice RoadRunners BRR-L & BBR-LA Programming GuideData Capture for Workforce in MotionRoadRunners BRR-L & BRR-LA Programming Guide RoadRunners BRR-L & BRR-LA Programming guide Nov2/ GENERAL CONFIGURATION 3/ DECODER SETTINGS3/29 1/ Introduction2.2/ Erase all barcodes in memory 2/ General Configuration2.1/ Reset all parameters 2.3/ Baracoda advanced features5/29 2.3.2/ Shutdown timers2.3.3/ No data loss mode and Baracoda Header Baracoda header No data loss mode2.3.4/ Timestamp Option Programming procedure for “set Timestamp” option6/29 7/29 2.4/ Reading ModeREAL TIME with ACK beep and bufferisation 2.5/ Operating Mode2.5.1/ Real time mode REAL TIME mode9/29 2.5.2/ Batch modeParameters are 2.7/ Buzzer and Led Settings2.6/ Cradle / RS232 jack 2.6.1/ Cradle 2.6.2/ RS232 jack11/29 2.8/ Bluetooth commands 2.8.1/ Bluetooth name12/29 2.8.2/ Sniff settings2.8.3/ Power emission settings 2.8.4/ Security code PIN settings13/29 2.9/ Prefix and suffix2.9.1/ Prefix/suffix RoadRunners BRR-L Programming guideFeature enabled for CPU firmware version ≥ 2.9.2/ Postrefix/postsuffix14/29 3.4/ Disable All Symbologies 3/ Decoder settings3.1/ Symbology default settings 3.2/ Symbology IdentifierProgramming procedure for “set barcode length” option 3.6/ Codabar settings3.5/ Set decoder barcode length RoadRunners BRR-L Programming guide3.8/ Code 39 settings 3.7/ Code 11 Settings17/29 18/29 3.9/ Code 93 SettingsCode 39 - format - full ASCII Code 39 - check digit - not used3.10.2/ EAN 128 Group Separator 3.10/ Code 128 Settings 3.10.1/ General19/29 3.12/ MSI Code Settings 3.11/ Interleaved 2 of 5 Settings20/29 3.14/ UPC/ EAN Settings 3.13/ Standard 2 of 5 Settings21/29 22/29 Programming procedure for “set min Max length” option 3.15/ Set min or Max length option23/29 Selected Symbology SELECT ALL Code Code 128 / EAN EAN 13 / UPC A Code CodabarInterleaved 2 of Standard 2 of 5 industrial 2 of Code MSI UPC E EAN Symbology tableName APPENDIX 1 ASCII Table A-Z, a-z, 0-9, ponctuation, Control charactersCapital letters A-Z 25/29a b c d e f g h i j k l m Ponctuation SpaceSmall letters a-z 26/2927/29 Decimal numbersNUL SOH STX TAB Control Characters28/29 CR EOT ETX LFCode 39 Option Values APPENDIXSymbology Character Modifier Characters