Baracoda BRR-L 3/ Decoder settings, 3.1/ Symbology default settings, 3.2/ Symbology Identifier

Page 15

RoadRunners BRR-L Programming guide

dec 2006

3/ Decoder settings

3.1/ Symbology default settings

Sets the defaults decoder settings for all the symbologies

Set Decoder Default Settings

3.2/ Symbology Identifier

AIM Identifier will be transmitted at the beginning of the barcode. More information about the AIM Identifier available in

Appendix2

Symbology identifier - AIM - not transmitted (*)

Symbology identifier - AIM - transmitted

3.3/ Voting

Standard voting set is 2. This means that a barcode is considered read by the decoder if the same data is decoded twice. Changing this parameters will enable a stronger security on the decoding of the barcode.

Voting = 3

Voting = 2 (*)

Voting = 4

3.4/ Disable All Symbologies

Even if all symbologies are disabled, the RoadRunners will always be able to read the programming barcodes of this document.

Disable all symbologies

Enable all symbologies

15/29

Image 15

Contents Important notice RoadRunners BRR-L & BBR-LA Programming GuideData Capture for Workforce in MotionRoadRunners BRR-L & BRR-LA Programming Guide RoadRunners BRR-L & BRR-LA Programming guide Nov2/ GENERAL CONFIGURATION 3/ DECODER SETTINGS3/29 1/ Introduction2.2/ Erase all barcodes in memory 2/ General Configuration2.1/ Reset all parameters 2.3/ Baracoda advanced features5/29 2.3.2/ Shutdown timers2.3.3/ No data loss mode and Baracoda Header Baracoda header No data loss modeProgramming procedure for “set Timestamp” option 2.3.4/ Timestamp Option6/29 7/29 2.4/ Reading ModeREAL TIME with ACK beep and bufferisation 2.5/ Operating Mode2.5.1/ Real time mode REAL TIME mode9/29 2.5.2/ Batch modeParameters are 2.7/ Buzzer and Led Settings2.6/ Cradle / RS232 jack 2.6.1/ Cradle 2.6.2/ RS232 jack11/29 2.8/ Bluetooth commands 2.8.1/ Bluetooth name12/29 2.8.2/ Sniff settings2.8.3/ Power emission settings 2.8.4/ Security code PIN settings13/29 2.9/ Prefix and suffix2.9.1/ Prefix/suffix RoadRunners BRR-L Programming guide2.9.2/ Postrefix/postsuffix Feature enabled for CPU firmware version ≥14/29 3.4/ Disable All Symbologies 3/ Decoder settings3.1/ Symbology default settings 3.2/ Symbology IdentifierProgramming procedure for “set barcode length” option 3.6/ Codabar settings3.5/ Set decoder barcode length RoadRunners BRR-L Programming guide3.7/ Code 11 Settings 3.8/ Code 39 settings17/29 18/29 3.9/ Code 93 SettingsCode 39 - format - full ASCII Code 39 - check digit - not used3.10/ Code 128 Settings 3.10.1/ General 3.10.2/ EAN 128 Group Separator19/29 3.11/ Interleaved 2 of 5 Settings 3.12/ MSI Code Settings20/29 3.13/ Standard 2 of 5 Settings 3.14/ UPC/ EAN Settings21/29 22/29 3.15/ Set min or Max length option Programming procedure for “set min Max length” option23/29 Selected Symbology SELECT ALL Code Code 128 / EAN EAN 13 / UPC A Code CodabarInterleaved 2 of Standard 2 of 5 industrial 2 of Code MSI UPC E EAN Symbology tableName APPENDIX 1 ASCII Table A-Z, a-z, 0-9, ponctuation, Control charactersCapital letters A-Z 25/29a b c d e f g h i j k l m Ponctuation SpaceSmall letters a-z 26/2927/29 Decimal numbersNUL SOH STX TAB Control Characters28/29 CR EOT ETX LFCode 39 Option Values APPENDIXSymbology Character Modifier Characters