Cisco Systems ONS 15454 manual DLP-A534 Provision OSI Routing Mode, 22-40

Page 40

Chapter 22 DLPs A500 to A599

DLP- A534 Provision OSI Routing Mode

DLP-A534 Provision OSI Routing Mode

Caution

Caution

Caution

Note

Purpose

This task provisions the Open System Interconnection (OSI) routing mode.

 

Complete this task when the ONS 15454 is connected to networks with

 

third party network elements (NEs) that use the OSI protocol stack for data

 

communications network (DCN) communication.

Tools/Equipment

None

Prerequisite Procedures

NTP-A323 Verify Card Installation, page 4-2

Required/As Needed

As needed

Onsite/Remote

Onsite

Security Level

Provisioning or higher

Do not complete this task until you confirm the role of the node within the network. It will be either an ES, IS Level 1, or IS Level 1/Level 2. This decision must be carefully considered. For additional information about OSI provisioning, refer to the “Management Network Connectivity” chapter of the Cisco ONS 15454 Reference Manual.

Link State Protocol (LSP) buffers must be the same at all NEs within the network, or loss of visibility might occur. Do not modify the LSP buffers unless you confirm that all NEs within the OSI have the same buffer size.

LSP buffer sizes cannot be greater than the LAP-D maximum transmission unit (MTU) size within the OSI area.

For ONS 15454 nodes, three virtual routers can be provisioned. The node primary NSAP address is also the Router 1 primary manual area address. To edit the primary NSAP, you must edit the Router 1 primary manual area address. After you enable Router 1 on the Routers subtab, the Change Primary Area Address button is available to edit the address.

Step 1 Complete the DLP-A60 Log into CTC, page 17-69at the node where you want to provision the OSI routing mode. If you are already logged in, continue with Step 2.

Step 2 In node view, click the Provisioning > OSI > Main Setup tabs.

Step 3 Choose a routing mode:

•End System—The ONS 15454 performs OSI end system (ES) functions and relies upon an intermediate system (IS) for communication with nodes that reside within its OSI area.

Note The End System routing mode is not available if more than one virtual router is enabled.

•Intermediate System Level 1—The ONS 15454 performs OSI IS functions. It communicates with IS and ES nodes that reside within its OSI area. It depends upon an IS L1/L2 node to communicate with IS and ES nodes that reside outside its OSI area.

 

Cisco ONS 15454 Procedure Guide, R7.0

22-40

November 2007

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DLP-A507 View OC-N PM Parameters 22-122-2 Card ViewDLP-A509 Provision CE-1000-4 Ethernet Ports Click the Provisioning Ether Ports tabsClick the Performance Ether Ports Statistics tabs 22-3DLP-A510 Provision a DS-3 Circuit Source and Destination 22-4DLP-A512 Change Node Access and PM Clearing Privilege 22-5DLP-A513 Provision CE-100T-8 Ethernet Ports 22-622-7 Click the Performance POS Ports Statistics tabs DLP-A514 Provision CE-100T-8 and CE-1000-4 POS Ports22-8 Click the History Shelf tabs DLP-A517 View Alarm or Event History22-9 Alarm Profile Editor tabs Figure DLP-A518 Create a New or Cloned Alarm Severity Profile22-10 Node View Alarm Profile Editor 22-1122-12 22-13 Store Profiles Dialog BoxClick the Provisioning Alarm Profiles Alarm Behavior tabs DLP-A519 Apply Alarm Profiles to Ports22-14 DLP-A520 Delete Alarm Severity Profiles 22-1522-16 Select Node/Profile Combination For Delete Dialog BoxAlarm Filter Dialog Box General Tab 22-17Alarm Filter Dialog Box Conditions Tab 22-18DLP-A522 Suppress Alarm Reporting 22-19DLP-A523 Discontinue Alarm Suppression 22-20DLP-A524 Download an Alarm Severity Profile 22-21Or Sonet Thresholds subtab Click OK22-22 Parameter Description Options 22-23IS-NR 22-2422-25 DLP-A527 Change the OC-N Card ALS Maintenance Settings 22-26Cisco ONS 15454 Reference Manual 22-27DLP-A529 Delete Ethernet Rmon Alarm Thresholds DLP-A528 Change the Default Network View Background Map22-28 DLP-A530 Install the Tie-Down Bar 22-29DLP-A531 Print CTC Data 22-3022-31 Selecting CTC Data For PrintDLP-A532 Export CTC Data 22-3222-33 DLP-A533 Create Ethernet Rmon Alarm Thresholds 22-34Variable Definition 22-3522-36 22-37 22-38 22-39 DLP-A534 Provision OSI Routing Mode 22-40DLP-A535 Provision or Modify Tarp Operating Parameters Node view, click the Provisioning OSI Tarp Config tabs22-41 22-42 Click Add Static Entry Node view, click the Provisioning OSI Tarp Static TDC tabs22-43 Click Delete Static Entry DLP-A538 Add a Tarp Manual Adjacency Table Entry22-44 DLP-A539 Provision OSI Routers 22-45DLP-A540 Provision Additional Manual Area Addresses DLP-A541 Enable the OSI Subnet on the LAN Interface22-46 22-47 DLP-A542 Create an IP-Over-CLNS Tunnel 22-48DLP-A543 Remove a Tarp Manual Adjacency Table Entry DLP-A544 Change the OSI Routing Mode22-49 22-50 DLP-A545 Edit the OSI Router Configuration DLP-A546 Edit the OSI Subnetwork Point of AttachmentNode view, click the Provisioning OSI Routers Subnet tabs 22-51DLP-A547 Edit an IP-Over-CLNS Tunnel 22-52DLP-A548 Delete an IP-Over-CLNS Tunnel 22-53DLP-A549 View IS-IS Routing Information Base 22-54Node view, click the Maintenance OSI ES-IS RIB tabs DLP-A550 View ES-IS Routing Information BaseDLP-A551 Manage the Tarp Data Cache 22-55DLP-A552 Adjust the Java Virtual Memory Heap Size 22-5622-57 22-58 22-59 22-60 22-61 22-62 22-63 Click the Maintenance Protection tabs 22-6422-65 22-66
Related manuals
Manual 54 pages 43.54 Kb

ONS 15454 specifications

Cisco Systems ONS 15454 is a versatile optical networking platform designed to enable service providers and enterprises to deploy and manage robust optical networks efficiently. The ONS 15454 serves as a cornerstone in the evolution of transport networks, featuring various technologies that meet the increasing demand for bandwidth and service quality.

One of the standout features of the ONS 15454 is its support for multiple service types, including TDM, Ethernet, and Wavelength Division Multiplexing (WDM). This capability allows service providers to maximize network resources while delivering a wide range of services, from traditional voice to high-speed data and video.

The ONS 15454 leverages Dense Wavelength Division Multiplexing (DWDM) technology, enabling the transmission of multiple data streams over a single optical fiber. This effectively expands the network's capacity without the need for additional infrastructure, a crucial benefit in today's ever-growing data landscape. The system supports a variety of transponder modules, allowing for flexible scaling and seamless upgrades as bandwidth requirements increase.

Scalability is another key characteristic of the ONS 15454. With its modular architecture, it accommodates a range of interfaces and line cards, making it easier to tailor deployments to specific customer needs. This modularity not only facilitates upgrades but also simplifies maintenance, minimizing downtime and operational costs.

The platform also features advanced management capabilities through Cisco's Optical Network Management system. This allows for real-time monitoring, provisioning, and troubleshooting, ensuring network reliability and performance. The intuitive interface and comprehensive reporting tools enable operators to gain insights into network operations, improving decision-making processes.

Furthermore, the ONS 15454 is built to support optical layer protection features, enhancing network resilience. Technologies such as Automatic Protection Switching (APS) and Optical Supervisory Channel (OSC) ensure that connectivity is maintained even in the event of a failure, crucial for mission-critical applications.

In conclusion, the Cisco ONS 15454 is a powerful optical networking solution that combines flexibility, scalability, and advanced management features. Its support for various services and technologies positions it as an essential asset for organizations looking to build a future-proof network capable of handling increasing data traffic while maintaining high service standards.
Top Page Image Contents