Cisco Systems ONS 15454 manual DLP-A514 Provision CE-100T-8 and CE-1000-4 POS Ports, 22-8

Page 8

Chapter 22 DLPs A500 to A599

DLP- A514 Provision CE-100T-8 and CE-1000-4 POS Ports

DLP-A514 Provision CE-100T-8 and CE-1000-4 POS Ports

Purpose

This task provisions CE-100T-8 or CE-1000-4 POS ports to carry traffic.

Tools/Equipment

None

Prerequisite Procedures

DLP-A60 Log into CTC, page 17-69

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Note You can provision SONET CCAT or VCAT circuits for the CE-100T-8 or CE-1000-4 before or after provisioning the card’s Ethernet ports and/or POS ports. See the “NTP-A257 Create an Automatically Routed Optical Circuit” procedure on page 6-38or the “NTP-A264 Create an Automatically Routed VCAT Circuit” procedure on page 6-82, as needed.

Step 1 In node view, double-click the CE-100T-8 or CE-1000-4 card graphic to open the card. Step 2 Click the Provisioning > POS Ports tabs.

Step 3 For each CE-100T-8 or CE-1000-4 port, provision the following parameters:

•Port Name—If you want to label the port, enter the port name.

•Admin State—Choose IS to put the port in service.

•Framing Type—Choose GPF-FPOS framing (the default) or HDLC POS framing. The framing type needs to match the framing type of the POS device at the end of the SONET circuit.

•Encap CRC—With GFP-F framing, the user can configure a 32-bitcyclic redundancy check (CRC) (the default) or none (no CRC). HDLC framing provides a set 32-bit CRC. The CRC should be set to match the CRC of the POS device on the end of the SONET circuit.

Note For more details about the interoperabilty of Optical Networking System (ONS) Ethernet cards, including information on encapsulation, framing, and CRC, refer to the “POS on ONS Ethernet Cards” chapter of the Ethernet Card Software Feature and Configuration Guide for the Cisco ONS 15454, Cisco ONS 15454 SDH, and Cisco ONS 15327.

Note The CE-100T-8 and CE-1000-4 cards use LEX encapsulation, which is the primary POS encapsulation used in ONS Ethernet cards.

Step 4 Click Apply.

Step 5 Refresh the POS statistics:

a.Click the Performance > POS Ports > Statistics tabs.

b.Click Refresh.

Step 6 Return to your originating procedure (NTP).

 

Cisco ONS 15454 Procedure Guide, R7.0

22-8

November 2007

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DLP-A507 View OC-N PM Parameters 22-122-2 Card ViewDLP-A509 Provision CE-1000-4 Ethernet Ports Click the Provisioning Ether Ports tabsClick the Performance Ether Ports Statistics tabs 22-3DLP-A510 Provision a DS-3 Circuit Source and Destination 22-4DLP-A512 Change Node Access and PM Clearing Privilege 22-5DLP-A513 Provision CE-100T-8 Ethernet Ports 22-622-7 22-8 DLP-A514 Provision CE-100T-8 and CE-1000-4 POS PortsClick the Performance POS Ports Statistics tabs 22-9 DLP-A517 View Alarm or Event HistoryClick the History Shelf tabs 22-10 DLP-A518 Create a New or Cloned Alarm Severity ProfileAlarm Profile Editor tabs Figure Node View Alarm Profile Editor 22-1122-12 22-13 Store Profiles Dialog Box22-14 DLP-A519 Apply Alarm Profiles to PortsClick the Provisioning Alarm Profiles Alarm Behavior tabs DLP-A520 Delete Alarm Severity Profiles 22-1522-16 Select Node/Profile Combination For Delete Dialog BoxAlarm Filter Dialog Box General Tab 22-17Alarm Filter Dialog Box Conditions Tab 22-18DLP-A522 Suppress Alarm Reporting 22-19DLP-A523 Discontinue Alarm Suppression 22-20DLP-A524 Download an Alarm Severity Profile 22-2122-22 Click OKOr Sonet Thresholds subtab Parameter Description Options 22-23IS-NR 22-2422-25 DLP-A527 Change the OC-N Card ALS Maintenance Settings 22-26Cisco ONS 15454 Reference Manual 22-2722-28 DLP-A528 Change the Default Network View Background MapDLP-A529 Delete Ethernet Rmon Alarm Thresholds DLP-A530 Install the Tie-Down Bar 22-29DLP-A531 Print CTC Data 22-3022-31 Selecting CTC Data For PrintDLP-A532 Export CTC Data 22-3222-33 DLP-A533 Create Ethernet Rmon Alarm Thresholds 22-34Variable Definition 22-3522-36 22-37 22-38 22-39 DLP-A534 Provision OSI Routing Mode 22-4022-41 Node view, click the Provisioning OSI Tarp Config tabsDLP-A535 Provision or Modify Tarp Operating Parameters 22-42 22-43 Node view, click the Provisioning OSI Tarp Static TDC tabsClick Add Static Entry 22-44 DLP-A538 Add a Tarp Manual Adjacency Table EntryClick Delete Static Entry DLP-A539 Provision OSI Routers 22-4522-46 DLP-A541 Enable the OSI Subnet on the LAN InterfaceDLP-A540 Provision Additional Manual Area Addresses 22-47 DLP-A542 Create an IP-Over-CLNS Tunnel 22-4822-49 DLP-A544 Change the OSI Routing ModeDLP-A543 Remove a Tarp Manual Adjacency Table Entry 22-50 DLP-A545 Edit the OSI Router Configuration DLP-A546 Edit the OSI Subnetwork Point of AttachmentNode view, click the Provisioning OSI Routers Subnet tabs 22-51DLP-A547 Edit an IP-Over-CLNS Tunnel 22-52DLP-A548 Delete an IP-Over-CLNS Tunnel 22-53DLP-A549 View IS-IS Routing Information Base 22-54Node view, click the Maintenance OSI ES-IS RIB tabs DLP-A550 View ES-IS Routing Information BaseDLP-A551 Manage the Tarp Data Cache 22-55DLP-A552 Adjust the Java Virtual Memory Heap Size 22-5622-57 22-58 22-59 22-60 22-61 22-62 22-63 Click the Maintenance Protection tabs 22-6422-65 22-66
Related manuals
Manual 54 pages 43.54 Kb

ONS 15454 specifications

Cisco Systems ONS 15454 is a versatile optical networking platform designed to enable service providers and enterprises to deploy and manage robust optical networks efficiently. The ONS 15454 serves as a cornerstone in the evolution of transport networks, featuring various technologies that meet the increasing demand for bandwidth and service quality.

One of the standout features of the ONS 15454 is its support for multiple service types, including TDM, Ethernet, and Wavelength Division Multiplexing (WDM). This capability allows service providers to maximize network resources while delivering a wide range of services, from traditional voice to high-speed data and video.

The ONS 15454 leverages Dense Wavelength Division Multiplexing (DWDM) technology, enabling the transmission of multiple data streams over a single optical fiber. This effectively expands the network's capacity without the need for additional infrastructure, a crucial benefit in today's ever-growing data landscape. The system supports a variety of transponder modules, allowing for flexible scaling and seamless upgrades as bandwidth requirements increase.

Scalability is another key characteristic of the ONS 15454. With its modular architecture, it accommodates a range of interfaces and line cards, making it easier to tailor deployments to specific customer needs. This modularity not only facilitates upgrades but also simplifies maintenance, minimizing downtime and operational costs.

The platform also features advanced management capabilities through Cisco's Optical Network Management system. This allows for real-time monitoring, provisioning, and troubleshooting, ensuring network reliability and performance. The intuitive interface and comprehensive reporting tools enable operators to gain insights into network operations, improving decision-making processes.

Furthermore, the ONS 15454 is built to support optical layer protection features, enhancing network resilience. Technologies such as Automatic Protection Switching (APS) and Optical Supervisory Channel (OSC) ensure that connectivity is maintained even in the event of a failure, crucial for mission-critical applications.

In conclusion, the Cisco ONS 15454 is a powerful optical networking solution that combines flexibility, scalability, and advanced management features. Its support for various services and technologies positions it as an essential asset for organizations looking to build a future-proof network capable of handling increasing data traffic while maintaining high service standards.
Top Page Image Contents