Cisco Systems ONS 15454 manual DLP-A540 Provision Additional Manual Area Addresses, 22-46

Page 46

Chapter 22 DLPs A500 to A599

DLP- A540 Provision Additional Manual Area Addresses

DLP-A540 Provision Additional Manual Area Addresses

 

Purpose

This task provisions the OSI manual area addresses. One primary and two

 

 

additional manual areas can be created for each virtual router.

 

Tools/Equipment

None

 

Prerequisite Procedures

DLP-A539 Provision OSI Routers, page 22-45

 

 

DLP-A60 Log into CTC, page 17-69

 

Required/As Needed

As needed

 

Onsite/Remote

Onsite or remote

 

Security Level

Provisioning or higher

 

 

Step 1

In node view, click the Provisioning > OSI > Routers > Setup tabs.

Step 2

Chose the router where you want provision an additional manual area address and click Edit. The OSI

 

Router Editor dialog box.

 

Step 3

In the OSI Router Editor dialog box:

a.Check Enable Router to enable the router and make its primary area address available for editing.

b.Click the manual area address, then click Add.

c.In the Add Manual Area Address dialog box, enter the primary area address in the Area Address field. If you prefer, click Use Mask and enter the address in the Masked NSAP Entry dialog box. The address (hexadecimal format) can be 2 to 24 alphanumeric characters (0–9, a–f) in length.

d.Click OK successively to close the following dialog boxes: Masked NSAP Entry (if used), Add Manual Area Address, and OSI Router Editor.

Step 4 Return to your originating procedure (NTP).

DLP-A541 Enable the OSI Subnet on the LAN Interface

Purpose

This task enables the OSI subnetwork point of attachment on the LAN

 

interface.

Tools/Equipment

None

Prerequisite Procedures

DLP-A60 Log into CTC, page 17-69

Required/As Needed

As needed

Onsite/Remote

Onsite or remote

Security Level

Provisioning or higher

Note OSI subnetwork points of attachment are enabled on DCCs when you create DCCs. See the “DLP-A377 Provision Section DCC Terminations” task on page 20-69and the “DLP-A378 Provision Line DCC Terminations” task on page 20-71.

 

Cisco ONS 15454 Procedure Guide, R7.0

22-46

November 2007

Page 45 Page 47
Image 46
Page 45 Page 47
Contents DLP-A507 View OC-N PM Parameters 22-122-2 Card ViewClick the Performance Ether Ports Statistics tabs DLP-A509 Provision CE-1000-4 Ethernet PortsClick the Provisioning Ether Ports tabs 22-3DLP-A510 Provision a DS-3 Circuit Source and Destination 22-4DLP-A512 Change Node Access and PM Clearing Privilege 22-5DLP-A513 Provision CE-100T-8 Ethernet Ports 22-622-7 Click the Performance POS Ports Statistics tabs DLP-A514 Provision CE-100T-8 and CE-1000-4 POS Ports22-8 Click the History Shelf tabs DLP-A517 View Alarm or Event History22-9 Alarm Profile Editor tabs Figure DLP-A518 Create a New or Cloned Alarm Severity Profile22-10 Node View Alarm Profile Editor 22-1122-12 22-13 Store Profiles Dialog BoxClick the Provisioning Alarm Profiles Alarm Behavior tabs DLP-A519 Apply Alarm Profiles to Ports22-14 DLP-A520 Delete Alarm Severity Profiles 22-1522-16 Select Node/Profile Combination For Delete Dialog BoxAlarm Filter Dialog Box General Tab 22-17Alarm Filter Dialog Box Conditions Tab 22-18DLP-A522 Suppress Alarm Reporting 22-19DLP-A523 Discontinue Alarm Suppression 22-20DLP-A524 Download an Alarm Severity Profile 22-21Or Sonet Thresholds subtab Click OK22-22 Parameter Description Options 22-23IS-NR 22-2422-25 DLP-A527 Change the OC-N Card ALS Maintenance Settings 22-26Cisco ONS 15454 Reference Manual 22-27DLP-A529 Delete Ethernet Rmon Alarm Thresholds DLP-A528 Change the Default Network View Background Map22-28 DLP-A530 Install the Tie-Down Bar 22-29DLP-A531 Print CTC Data 22-3022-31 Selecting CTC Data For PrintDLP-A532 Export CTC Data 22-3222-33 DLP-A533 Create Ethernet Rmon Alarm Thresholds 22-34Variable Definition 22-3522-36 22-37 22-38 22-39 DLP-A534 Provision OSI Routing Mode 22-40DLP-A535 Provision or Modify Tarp Operating Parameters Node view, click the Provisioning OSI Tarp Config tabs22-41 22-42 Click Add Static Entry Node view, click the Provisioning OSI Tarp Static TDC tabs22-43 Click Delete Static Entry DLP-A538 Add a Tarp Manual Adjacency Table Entry22-44 DLP-A539 Provision OSI Routers 22-45DLP-A540 Provision Additional Manual Area Addresses DLP-A541 Enable the OSI Subnet on the LAN Interface22-46 22-47 DLP-A542 Create an IP-Over-CLNS Tunnel 22-48DLP-A543 Remove a Tarp Manual Adjacency Table Entry DLP-A544 Change the OSI Routing Mode22-49 22-50 Node view, click the Provisioning OSI Routers Subnet tabs DLP-A545 Edit the OSI Router ConfigurationDLP-A546 Edit the OSI Subnetwork Point of Attachment 22-51DLP-A547 Edit an IP-Over-CLNS Tunnel 22-52DLP-A548 Delete an IP-Over-CLNS Tunnel 22-53DLP-A549 View IS-IS Routing Information Base 22-54DLP-A551 Manage the Tarp Data Cache Node view, click the Maintenance OSI ES-IS RIB tabsDLP-A550 View ES-IS Routing Information Base 22-55DLP-A552 Adjust the Java Virtual Memory Heap Size 22-5622-57 22-58 22-59 22-60 22-61 22-62 22-63 Click the Maintenance Protection tabs 22-6422-65 22-66
Related manuals
Manual 54 pages 43.54 Kb

ONS 15454 specifications

Cisco Systems ONS 15454 is a versatile optical networking platform designed to enable service providers and enterprises to deploy and manage robust optical networks efficiently. The ONS 15454 serves as a cornerstone in the evolution of transport networks, featuring various technologies that meet the increasing demand for bandwidth and service quality.

One of the standout features of the ONS 15454 is its support for multiple service types, including TDM, Ethernet, and Wavelength Division Multiplexing (WDM). This capability allows service providers to maximize network resources while delivering a wide range of services, from traditional voice to high-speed data and video.

The ONS 15454 leverages Dense Wavelength Division Multiplexing (DWDM) technology, enabling the transmission of multiple data streams over a single optical fiber. This effectively expands the network's capacity without the need for additional infrastructure, a crucial benefit in today's ever-growing data landscape. The system supports a variety of transponder modules, allowing for flexible scaling and seamless upgrades as bandwidth requirements increase.

Scalability is another key characteristic of the ONS 15454. With its modular architecture, it accommodates a range of interfaces and line cards, making it easier to tailor deployments to specific customer needs. This modularity not only facilitates upgrades but also simplifies maintenance, minimizing downtime and operational costs.

The platform also features advanced management capabilities through Cisco's Optical Network Management system. This allows for real-time monitoring, provisioning, and troubleshooting, ensuring network reliability and performance. The intuitive interface and comprehensive reporting tools enable operators to gain insights into network operations, improving decision-making processes.

Furthermore, the ONS 15454 is built to support optical layer protection features, enhancing network resilience. Technologies such as Automatic Protection Switching (APS) and Optical Supervisory Channel (OSC) ensure that connectivity is maintained even in the event of a failure, crucial for mission-critical applications.

In conclusion, the Cisco ONS 15454 is a powerful optical networking solution that combines flexibility, scalability, and advanced management features. Its support for various services and technologies positions it as an essential asset for organizations looking to build a future-proof network capable of handling increasing data traffic while maintaining high service standards.
Top Page Image Contents