Cisco Systems uBR7200 manual Port Adapter Installation Safety Information

Page 87

Port Adapter Installation Safety Information

Note Failure to install the port adapter in accordance with these instructions will invalidate the agency approvals for the Cisco uBR7200 series universal broadband router.

Disconnect the chassis from the power supply before removing any covers.

Disconnect the chassis from any analog telephone circuits or digital networks (where applicable) before removing any covers.

Make sure that the chassis is connected to earth ground during normal operation.

Do not work on the system or connect and disconnect cables during a lightning storm.

Make sure that the digital network interface cables are disconnected from digital network port adapters before removing the port adapters from the chassis. The digital network interface cables must remain disconnected from the digital network port adapters until after the port adapters are reinstalled in the chassis. (The host chassis provides the necessary protection for the operator.)

Caution Unless noted otherwise, the port adapter contains safety extra-low voltage (SELV) circuitry. Ensure that attachments at the interconnection ports of the apparatus are also SELV circuits. (SELV circuits are so designed and protected that, under both normal conditions and a likely fault condition, the voltage that can be drawn is not hazardous.)

The following operating conditions are required within the European Community:

The ports marked “Ethernet,” “10BaseT,” “TokenRing,” “FDDI,” “Console,” and “AUX” are SELV circuits. SELV circuits should only be connected to other SELV circuits.

Connection of AC power supply: the Cisco uBR7200 series is intended for use when supplied with AC power from a power source providing 7A maximum at 100 VAC and 3.5A maximum at

240 VAC, 50/60 Hz, with the chassis fully configured.

Connection of DC power supply: the Cisco uBR7200 series is intended for use when supplied with DC power from a power source providing 13A maximum at –48 VDC and 8A maximum at

–60 VDC, with the chassis fully configured.

Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with EN60950:1992.

Except in Australia, the PA-2CE1, PA-8B-ST, PA-4E1G-75, and PA-4E1G-120 port adapters are designated SELV within the scope of EN60950:1992. Users are reminded that ports on these port adapters should only be connected to SELV ports on other equipment in accordance with EN60950 clause 2.3.

This customer equipment must be installed and maintained by service personnel as defined by AS/NZ3260 clause 1.2.14.3 Service Personnel. Incorrect connection of equipment to the General Purpose Outlet could result in a hazardous situation.

Safety requirements are not fulfilled unless the equipment is connected to a wall socket outlet with protective earth ground.

Regulatory Compliance and Safety Information for the Cisco uBR7200 Series Universal Broadband Routers

 

78-14140-05

87

 

 

 

Image 87
Contents Revision Date Revision HistoryTranslated Safety Warnings Statement 5-Chassis Lifting Warning Translated Safety Warnings Translated Safety Warnings Statement 12-Power Supply Disconnection Warning Statement 43-Jewelry Removal Warning Translated Safety Warnings Statement 48-Stacking the Chassis Warning Statement 61-Power Supply Wiring Warning Statement 89-Telecommunications Lines Warning Statement 164-Two Person Lifting Requirement Statement 106-More Than One Power CordStatement 181-Wrist Strap and Midplane Contact Warning Translated Safety Warnings Statement 196-Chassis Disconnection Warning Translated Safety Warnings Statement 285-Electrical Connection Warning Statement 342-Before Connecting to System Power Supply Statement 1001-Work During Lightning Activity Statement 1003-DC Power DisconnectionTranslated Safety Warnings Statement 1004-Installation Instructions Translated Safety Warnings Translated Safety Warnings Translated Safety Warnings Translated Safety Warnings Page Statement 1007-TN and IT Power Systems Statement 1008-Class 1 Laser Product Statement 1015-Battery Handling Waarschuwing Onzichtbare laserstraling aanwezig Statement 1016-Invisible Laser RadiationStatement 1017-Restricted Area Translated Safety Warnings Statement 1018-Supply Circuit Statement 1021-SELV Circuit Translated Safety Warnings Statement 1022-Disconnect Device Statement 1023-No AWG Statement 1024-Ground Conductor Translated Safety Warnings Statement 1025-Use Copper Conductors Only Till enheten Statement 1026-WAN Port Static ShockStatement 1027-Class 1 LED Product Statement 1028-More Than One Power Supply Translated Safety Warnings Statement 1029-Blank Faceplates and Cover Panels Translated Safety Warnings 78-14140-05 Statement 1030-Equipment Installation Statement 1032-Lifting the Chassis Translated Safety Warnings Statement 1033-SELV-IEC 60950 DC Power Supply Statement 1040-Product Disposal Statement 1041-Disconnecting Telephone-Network Cables Statement 1043-Installation Hazard Translated Safety Warnings Statement 1045-Short-circuit Protection Translated Safety Warnings Statement 1046-Installing or Replacing the Unit Translated Safety Warnings Statement 1047-Overheating Prevention Statement 1051-Laser Radiation Translated Safety Warnings Statement 1064-Grounded Equipment Bewaar Deze Instructies Statement 1071-Warning DefinitionsBewahren SIE Diese Hinweise GUT AUF Spara Dessa Anvisningar GEM Disse Anvisninger Page Translated Safety Warnings Translated Safety Warnings Statement 36-Warning for Sweden European DirectivesStatement 25-Warning for Norway and Sweden Statement 35-Warning for FinlandFCC Declaration of Conformity Information for USA only Regulatory Standards Compliance Specification DescriptionSpecification Description IDA TS CM2 Acif C559 Korean Certification Information Class a Notice for FCC EMC Class a Notices and WarningsStatement 340-Class a Warning for CISPR22 Class a Notice for CanadaStatement 191-VCCI Class a Warning for Japan Class B Notice for FCC EMC Class B Notices and WarningsClass B Notice for Canada Port Adapter Compliance Information GR-1089-Core Intrabuilding Lightning-Immunity RequirementsFCC Part 68 Notice Approval Number CS-03 Certification for CanadaApplicant Name Model Number Approval Number Jate Certification for JapanRRL Certification for Korea Port Adapter Installation Safety InformationPort Adapter Installation Safety Information Related Documentation Cisco IOS Cmts Cable Command Reference at the following URL
Related manuals
Manual 88 pages 44.59 Kb