Cisco Systems XR 12000 Series specifications Contents

Page 1

Cisco XR 12000 Series Router

Ethernet Line Card Installation

December 10, 2008

Document Part Number: OL-7861-01

This guide contains instructions for installing Ethernet line cards in supported Cisco XR 12000 Series Routers. Also included are basic troubleshooting techniques to help in line card installation.

Contents

This installation guide includes the following sections:

•Important Information, page 2

•Product Overviews, page 4

•Preparing for Installation, page 9

•Removing and Installing a Line Card, page 10

•Removing and Installing EPAs, page 15

•Removing and Installing GBICs, page 23

•Removing and Installing SFP Modules, page 26

•Line Card Cable-Management Bracket, page 37

•Cabling and Specifications, page 42

•Verifying and Troubleshooting the Installation, page 58

•Line Card Memory, page 65

•Regulatory, Compliance, and Safety Information, page 79

•Obtaining Documentation and Submitting a Service Request, page 83

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 2008 Cisco Systems, Inc. All rights reserved.

Image 1

Contents Contents Important Information Router Hardware InstallationEthernet Line Card Product Numbers Supported PlatformsPart Number Minimum IOS Software Release Hardware Version Line Card RequiredMemory Options Product OverviewsRelated Documentation Ethernet Line Card ComparisonPart Number Port Gigabit Ethernet ISE Line CardPort 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Safety Guidelines Preparing for InstallationPreventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a Line CardRemoving a Line Card Guidelines for Line Card Removal and InstallationLine Card Removal and Installation Installing a Line Card Ejector Levers Removing an EPA from the Modular Gigabit Ethernet Line Card Removing and Installing EPAsRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Inserting the 2 screws on the Faceplate of the Line Card Removing and Installing GBICsRemoving the Gbic from an Ethernet Line Card General Gbic Handling and Maintenance GuidelinesRemoving and Replacing a Gbic Inserting a Gbic into the Gigabit Ethernet InterfaceBale Clasp SFP Module Removing and Installing SFP ModulesRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Mylar Tab SFP Module Installing a Bale Clasp SFP ModuleMylar Tab SFP Module Removing a Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleRemoving an Actuator Button SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Slide Tab SFP Module Installing an Actuator Button SFP ModuleSlide Tab SFP Module Removing a Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Installing a Slide Tab SFP ModuleLine Card Cable-Management Bracket Installing a Slide Tab SFP ModuleSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Fast Ethernet Interface Cabling and SpecificationsSC-Type Parameter RJ-45Parameter Gigabit Ethernet Interface Gbic Module Distance Connector Type Wavelength Fiber TypeGbic Laser Optical Transceiver Modules Power Sensitivity Budget Gbic Module Distance1 Connector Type Wavelength Fiber TypeTransmit Receive Link Gbic Product Number Cwdm Gbic Wavelength Color Identifier Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line CardGeneral Cwdm Gbic Installation and Usage Guidelines Card carrier side of line card Gigabit Ethernet SFP ModulesTransceiver Budget Power Sensitivity Distance Power Transmit Receive Typical MaximumSFP Module Type Wavelength Cable Distance Gigabit Ethernet Fiber-Optic Interface CablesTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Simplex LC Cable Connector Removing and Installing Fiber-Optic Interface CablesRemoving Fiber-Optic Interface Cables Disconnecting Line Card Interface Cables Installing Fiber-Optic Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module TX connector Simplex cables RX connector Duplex cable Cleaning Fiber-Optic ConnectorsType RJ-45 100BASE-T Copper Cables Removing and Installing RJ-45 100BASE-T Copper CableInstalling RJ-45 Cables Verifying and Troubleshooting the InstallationRemoving RJ-45 Cables Status LEDs Initial Boot ProcessGigabit Ethernet Status LEDs Color/Activity Description Alphanumeric LEDsNnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Locations Line Card MemoryEthernet Line Card Hardware Engine ISE Line Card Memory Locations Engine 2 Line Card Memory LocationsISE Line Card Memory Locations Ethernet Line Card Route Memory Options Engine 4 Line Card Memory LocationsCisco Product Number Dimm Module Ethernet Line Card Packet Memory Options Removing and Installing Line Card MemoryCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmInstalling a Dimm Handling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Moving the Plastic Latch Away from the Sodimm Installing a SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Retaining Clip Completely Installed into Module Latch Checking the Installation of Line Card MemoryTranslated Safety Warnings and Agency Approvals Regulatory, Compliance, and Safety InformationElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceEurope EU CanadaClass a Notice for Hungary Vcci Class a Notice for Japan Laser SafetyClass a Notice for Korea Obtaining Documentation and Submitting a Service Request OL-7861-01