Cisco Systems XR 12000 Series specifications Port 10-Gigabit Ethernet Line Card

Page 8

Product Overviews

1-Port 10-Gigabit Ethernet Line Card

The 1-Port 10-Gigabit Ethernet line card provides the supported Cisco XR 12000 Series Routers with one optical 802.3ae 10-Gigabit Ethernet interface. This interface provides a high-speed connection to other network devices, such as Cisco XR 12000 Series Routers, or to other routers or layer-2 or layer-3 switches that support 10-Gigabit Ethernet interfaces. Figure 3 shows the front view of the line card.

The port on the front panel of the line card is port number 0. This port uses a hardwired laser optical transceiver to provide a 10-Gigabit Ethernet optical interface. The transceiver consists of two optical interfaces—laser transmit (TX) and laser receive (RX)—that use SC connectors.

Next to the port on the line card are three green LEDs, aligned vertically and labeled from top to bottom as follows: LINK, ACTIVE, and RX FRAME.

Figure 3

1-Port 10-Gigabit Ethernet Line Card

 

 

LINK

98893

 

 

 

 

 

ACTIVE

 

 

 

RX FRAME

 

TX

RX

 

1X10GE-LR-SC

1

2

3

4

5

6

1

Ejector lever

3

RX port

5

Alphanumeric LEDs

 

 

 

 

 

 

2

TX port

4

Status LEDs

6

Ejector lever

 

 

 

 

 

 

Table 7 summarizes the optics and connectors used by the 1-Port 10-Gigabit Ethernet line card.

Table 7 1-Port 10-Gigabit Ethernet Line Card Optics and Connector Types

Part Number

Optics/Transmission

Maximum Distance

Connector Type

 

 

 

 

1X10GE-LR-SC

1550 nm (send),

20 km

SC

 

1300 nm-1570 nm (receive)

 

 

 

 

 

 

1X10GE-ER-SC

1550 nm (send),

75 km

SC

 

1300 nm-1570 nm (receive)

 

 

 

 

 

 

For more information, refer to the “10-Gigabit Ethernet” section on page 50 and the “Cabling and Specifications” section on page 42.

The 1-Port 10-Gigabit Ethernet line card ships with 256 MB of route processor memory and 512 MB of packet memory. The memory in the 1-Port 10-Gigabit Ethernet line card is not field replaceable. For more information on memory, see the “Line Card Memory” section on page 65.

Cisco XR 12000 Series Router Ethernet Line Card Installation

8

OL-7861-01

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Contents Router Hardware Installation Important InformationEthernet Line Card Product Numbers Supported PlatformsLine Card Required Part Number Minimum IOS Software Release Hardware VersionProduct Overviews Memory OptionsRelated Documentation Ethernet Line Card ComparisonPort Gigabit Ethernet ISE Line Card Part NumberPort 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Preventing Electrostatic Discharge Preparing for InstallationSafety Guidelines Removing and Installing a Line Card Required Tools and EquipmentGuidelines for Line Card Removal and Installation Removing a Line CardLine Card Removal and Installation Installing a Line Card Ejector Levers Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line CardRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Removing and Installing GBICs Inserting the 2 screws on the Faceplate of the Line CardGeneral Gbic Handling and Maintenance Guidelines Removing the Gbic from an Ethernet Line CardInserting a Gbic into the Gigabit Ethernet Interface Removing and Replacing a GbicRemoving and Installing SFP Modules Bale Clasp SFP ModuleRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP ModuleRemoving a Mylar Tab SFP Module Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleActuator Button SFP Module Removing an Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Installing an Actuator Button SFP Module Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Removing a Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Line Card Cable-Management BracketSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet InterfaceParameter Parameter RJ-45SC-Type Gbic Laser Optical Transceiver Modules Gbic Module Distance Connector Type Wavelength Fiber TypeGigabit Ethernet Interface Transmit Receive Link Gbic Module Distance1 Connector Type Wavelength Fiber TypePower Sensitivity Budget Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line Card Gbic Product Number Cwdm Gbic Wavelength Color IdentifierGeneral Cwdm Gbic Installation and Usage Guidelines Gigabit Ethernet SFP Modules Card carrier side of line cardSFP Module Type Wavelength Cable Distance Power Transmit Receive Typical MaximumTransceiver Budget Power Sensitivity Distance Transceiver Option Type Wavelength Fiber-Optic Interface CablesGigabit Ethernet SC cable connector Spring-action disconnect latch Removing and Installing Fiber-Optic Interface Cables Simplex LC Cable ConnectorRemoving Fiber-Optic Interface Cables Installing Fiber-Optic Interface Cables Disconnecting Line Card Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module Cleaning Fiber-Optic Connectors TX connector Simplex cables RX connector Duplex cableRemoving and Installing RJ-45 100BASE-T Copper Cable Type RJ-45 100BASE-T Copper CablesRemoving RJ-45 Cables Verifying and Troubleshooting the InstallationInstalling RJ-45 Cables Gigabit Ethernet Status LEDs Initial Boot ProcessStatus LEDs Alphanumeric LEDs Color/Activity DescriptionLED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Ethernet Line Card Hardware Engine Line Card MemoryLine Card Memory Locations Engine 2 Line Card Memory Locations ISE Line Card Memory LocationsISE Line Card Memory Locations Cisco Product Number Dimm Module Engine 4 Line Card Memory LocationsEthernet Line Card Route Memory Options Cisco Product Number Dimm Modules Dimm Sockets Removing and Installing Line Card MemoryEthernet Line Card Packet Memory Options Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Removing a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Installing a Sodimm Moving the Plastic Latch Away from the SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Completely Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe EUClass a Notice for Hungary Class a Notice for Korea Laser SafetyVcci Class a Notice for Japan Obtaining Documentation and Submitting a Service Request OL-7861-01

XR 12000 Series specifications

The Cisco Systems XR 12000 Series routers are designed to meet the demands of modern networking environments, ensuring high performance, scalability, and reliability for service providers and large enterprises. This series is engineered to deliver advanced features that facilitate a range of applications, including core routing, edge services, and data center interconnect.

One of the main features of the XR 12000 Series is its advanced routing capabilities. These routers utilize the Cisco IOS XR software architecture, which provides a modular and distributed operating system. This architecture enhances system reliability as individual processes can be restarted independently without affecting overall system operations. As a result, service providers can achieve higher uptime and enhanced service continuity.

The XR 12000 Series supports a robust set of technologies that enable efficient data handling and transport. Notably, the series includes support for Multiprotocol Label Switching (MPLS), which enhances traffic engineering, distributed bandwidth management, and Quality of Service (QoS) capabilities. This makes the XR 12000 a preferred choice for operators looking to optimize their network performance under increasing traffic loads.

Furthermore, the XR 12000 Series excels in scalability. With a flexible modular design, operators can customize their systems to fit specific needs by adding additional line cards or service modules. These enhancements enable operators to scale both up and down based on fluctuating demands, accommodating numerous high-bandwidth applications such as video streaming, cloud services, and IoT.

Security is another critical characteristic of the XR 12000 routers. Built-in cybersecurity features, including secure boot, strong encryption, and integrity checks, protect against unauthorized access and ensure data integrity. Coupled with advanced monitoring and logging capabilities, these routers can help operators maintain robust security postures.

Additionally, the XR 12000 Series is designed to facilitate seamless integration with existing network infrastructures. The routers support various protocols and interfaces, which ensure interoperability with legacy systems and enhance overall network efficiency. This flexibility allows service providers to future-proof their investments while adapting to evolving technological landscapes.

In summary, the Cisco XR 12000 Series routers stand out for their advanced routing capabilities, scalability, robust security features, and compatibility with modern and legacy network infrastructures. These attributes make them an ideal choice for organizations seeking to enhance their networking capabilities in a rapidly changing digital environment.
Top Page Image Contents