Cisco Systems XR 12000 Series specifications Preparing for Installation, Safety Guidelines

Page 9

Preparing for Installation

Preparing for Installation

The following sections provide information about preparing to install line cards:

•Safety Guidelines, page 9

•Preventing Electrostatic Discharge, page 9

•Required Tools and Equipment, page 10

Safety Guidelines

Before you perform any procedure in this publication, review the safety guidelines in this section to avoid injuring yourself or damaging the equipment.

The following guidelines are for your safety and to protect equipment. The guidelines do not include all hazards. Be alert.

Note Review the safety warnings listed in the Regulatory Compliance and Safety Information for

Cisco 12000 Series Internet Router publication (Document Number 78-4347-xx) that accompanied your router before installing, configuring, or maintaining a line card.

•Keep the work area clear and dust free during and after installation. Do not allow dirt or debris to enter into any laser-based components.

•Do not wear loose clothing, jewelry, or other items that could get caught in the router while working with line cards.

•Cisco equipment operates safely when it is used in accordance with its specifications and product usage instructions.

Before working with laser optics, read the “Laser Safety” section on page 82.

Preventing Electrostatic Discharge

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures. Electromagnetic interference (EMI) shielding is an integral component of the line card. We recommend using an ESD-preventive strap whenever you are handling network equipment or one of its components.

The following are guidelines for preventing ESD damage:

•Always use an ESD-preventive wrist or ankle strap and ensure that it makes good skin contact. Connect the equipment end of the connection cord to an ESD connection socket on the router or to bare metal on the chassis.

•Handle Ethernet line cards by the captive installation screws, the provided handle, ejector levers, or the line card metal carrier only; avoid touching the board or connector pins.

•Place removed Ethernet line cards board-side-up on an antistatic surface or in a static shielding bag. If you plan to return the component to the factory, immediately place it in a static shielding bag.

Cisco XR 12000 Series Router Ethernet Line Card Installation

 

OL-7861-01

9

 

 

 

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Contents Important Information Router Hardware InstallationEthernet Line Card Product Numbers Supported PlatformsPart Number Minimum IOS Software Release Hardware Version Line Card RequiredMemory Options Product OverviewsRelated Documentation Ethernet Line Card ComparisonPart Number Port Gigabit Ethernet ISE Line Card Port 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Preparing for Installation Safety GuidelinesPreventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a Line CardRemoving a Line Card Guidelines for Line Card Removal and InstallationLine Card Removal and Installation Installing a Line Card Ejector Levers Removing an EPA from the Modular Gigabit Ethernet Line Card Removing and Installing EPAsRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Inserting the 2 screws on the Faceplate of the Line Card Removing and Installing GBICsRemoving the Gbic from an Ethernet Line Card General Gbic Handling and Maintenance GuidelinesRemoving and Replacing a Gbic Inserting a Gbic into the Gigabit Ethernet InterfaceBale Clasp SFP Module Removing and Installing SFP ModulesRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Mylar Tab SFP Module Installing a Bale Clasp SFP ModuleMylar Tab SFP Module Removing a Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleRemoving an Actuator Button SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Slide Tab SFP Module Installing an Actuator Button SFP ModuleSlide Tab SFP Module Removing a Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Installing a Slide Tab SFP ModuleLine Card Cable-Management Bracket Installing a Slide Tab SFP ModuleSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Fast Ethernet Interface Cabling and SpecificationsParameter RJ-45 SC-TypeParameter Gbic Module Distance Connector Type Wavelength Fiber Type Gigabit Ethernet InterfaceGbic Laser Optical Transceiver Modules Gbic Module Distance1 Connector Type Wavelength Fiber Type Power Sensitivity BudgetTransmit Receive Link Gbic Product Number Cwdm Gbic Wavelength Color Identifier Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line CardGeneral Cwdm Gbic Installation and Usage Guidelines Card carrier side of line card Gigabit Ethernet SFP ModulesPower Transmit Receive Typical Maximum Transceiver Budget Power Sensitivity DistanceSFP Module Type Wavelength Cable Distance Fiber-Optic Interface Cables Gigabit EthernetTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Simplex LC Cable Connector Removing and Installing Fiber-Optic Interface CablesRemoving Fiber-Optic Interface Cables Disconnecting Line Card Interface Cables Installing Fiber-Optic Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module TX connector Simplex cables RX connector Duplex cable Cleaning Fiber-Optic ConnectorsType RJ-45 100BASE-T Copper Cables Removing and Installing RJ-45 100BASE-T Copper CableVerifying and Troubleshooting the Installation Installing RJ-45 CablesRemoving RJ-45 Cables Initial Boot Process Status LEDsGigabit Ethernet Status LEDs Color/Activity Description Alphanumeric LEDsNnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Line Card Memory LocationsEthernet Line Card Hardware Engine ISE Line Card Memory Locations Engine 2 Line Card Memory LocationsISE Line Card Memory Locations Engine 4 Line Card Memory Locations Ethernet Line Card Route Memory OptionsCisco Product Number Dimm Module Removing and Installing Line Card Memory Ethernet Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmInstalling a Dimm Handling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Moving the Plastic Latch Away from the Sodimm Installing a SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Retaining Clip Completely Installed into Module Latch Checking the Installation of Line Card MemoryTranslated Safety Warnings and Agency Approvals Regulatory, Compliance, and Safety InformationElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceEurope EU CanadaClass a Notice for Hungary Laser Safety Vcci Class a Notice for JapanClass a Notice for Korea Obtaining Documentation and Submitting a Service Request OL-7861-01
Top Page Image Contents