Cisco Systems XR 12000 Series specifications SC cable connector Spring-action disconnect latch

Page 51

Cabling and Specifications

•Single-mode—Generally yellow in color.

•Multimode—Generally gray or orange in color. Multimode cables are multifiber cables that carry 12 channels of fiber data.

Note For network applications using CWDM GBICs in Ethernet line cards, the CWDM GBICs use SMF patch cords only. Verify that all your patch cords are yellow (SMF), rather than orange (MMF).

The following types of cable connectors are used with Ethernet line cards:

•Subscriber connector (SC)—See Figure 36 and Figure 37

•Lucent connector (LC)— See Figure 38 and Figure 39

You can use two cables with simplex connectors, or one cable with dual, keyed connectors.

Warning Invisible laser radiation can be emitted from the aperture of the port when no cable is connected. Avoid exposure to laser radiation and do not stare into open apertures.

Figure 36 Simplex SC Cable Connector (Single-mode)

1 2

66917

1

SC cable connector

2

Spring-action disconnect latch

Figure 37 Duplex SC Cable Connector

242836

Cisco XR 12000 Series Router Ethernet Line Card Installation

	OL-7861-01	51

Image 51

Contents Contents Supported Platforms Router Hardware InstallationImportant Information Ethernet Line Card Product NumbersPart Number Minimum IOS Software Release Hardware Version Line Card RequiredEthernet Line Card Comparison Product OverviewsMemory Options Related DocumentationPart Number Port Gigabit Ethernet ISE Line CardPort 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Preparing for Installation Safety GuidelinesPreventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a Line CardRemoving a Line Card Guidelines for Line Card Removal and InstallationLine Card Removal and Installation Installing a Line Card Ejector Levers Removing an EPA from the Modular Gigabit Ethernet Line Card Removing and Installing EPAsRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Inserting the 2 screws on the Faceplate of the Line Card Removing and Installing GBICsRemoving the Gbic from an Ethernet Line Card General Gbic Handling and Maintenance GuidelinesRemoving and Replacing a Gbic Inserting a Gbic into the Gigabit Ethernet InterfaceBale Clasp SFP Module Removing and Installing SFP ModulesRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Mylar Tab SFP Module Installing a Bale Clasp SFP ModuleMylar Tab SFP Module Removing a Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleRemoving an Actuator Button SFP Module Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Slide Tab SFP Module Installing an Actuator Button SFP ModuleSlide Tab SFP Module Removing a Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Installing a Slide Tab SFP ModuleLine Card Cable-Management Bracket Installing a Slide Tab SFP ModuleSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Fast Ethernet Interface Cabling and SpecificationsParameter RJ-45 SC-TypeParameter Gbic Module Distance Connector Type Wavelength Fiber Type Gigabit Ethernet InterfaceGbic Laser Optical Transceiver Modules Gbic Module Distance1 Connector Type Wavelength Fiber Type Power Sensitivity BudgetTransmit Receive Link Gbic Product Number Cwdm Gbic Wavelength Color Identifier Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line CardGeneral Cwdm Gbic Installation and Usage Guidelines Card carrier side of line card Gigabit Ethernet SFP ModulesPower Transmit Receive Typical Maximum Transceiver Budget Power Sensitivity DistanceSFP Module Type Wavelength Cable Distance Fiber-Optic Interface Cables Gigabit EthernetTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Simplex LC Cable Connector Removing and Installing Fiber-Optic Interface CablesRemoving Fiber-Optic Interface Cables Disconnecting Line Card Interface Cables Installing Fiber-Optic Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module TX connector Simplex cables RX connector Duplex cable Cleaning Fiber-Optic ConnectorsType RJ-45 100BASE-T Copper Cables Removing and Installing RJ-45 100BASE-T Copper CableVerifying and Troubleshooting the Installation Installing RJ-45 CablesRemoving RJ-45 Cables Initial Boot Process Status LEDsGigabit Ethernet Status LEDs Color/Activity Description Alphanumeric LEDsNnnn LED Display Meaning SourceVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Line Card Memory LocationsEthernet Line Card Hardware Engine ISE Line Card Memory Locations Engine 2 Line Card Memory LocationsISE Line Card Memory Locations Engine 4 Line Card Memory Locations Ethernet Line Card Route Memory OptionsCisco Product Number Dimm Module Removing and Installing Line Card Memory Ethernet Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Dimm Socket with Dual Release Levers Removing a DimmInstalling a Dimm Handling a Dimm Removing a SodimmRemove Retaining Clip from Memory Module Socket Moving the Plastic Latch Away from the Sodimm Installing a SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Retaining Clip Completely Installed into Module Latch Checking the Installation of Line Card MemoryFCC Class a Compliance Regulatory, Compliance, and Safety InformationTranslated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory StatementsEurope EU CanadaClass a Notice for Hungary Laser Safety Vcci Class a Notice for JapanClass a Notice for Korea Obtaining Documentation and Submitting a Service Request OL-7861-01