Cisco Systems XR 12000 Series specifications Laser Safety, Vcci Class a Notice for Japan

Page 82

Regulatory, Compliance, and Safety Information

VCCI Class A Notice for Japan

Warning

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions. Statement 191

Class A Notice for Korea

Warning

This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type. Statement 294

Laser Safety

Single-mode Ethernet line cards (all of the line cards except 8-Port Fast Ethernet) are equipped with a Class 1 laser. Multimode Ethernet line cards (Gigabit Ethernet and 4-Port Gigabit Ethernet ISE) are equipped with a Class 1 LED. These devices emit invisible radiation. Do not stare into operational line card ports. The following laser warnings apply to the Ethernet line cards:

•Class 1 Laser Product Warning (Single-mode), page 83

•Class 1 LED Product Warning (Multimode), page 83

•General Laser Warning, page 83

Cisco XR 12000 Series Router Ethernet Line Card Installation

82	OL-7861-01

Image 82

Contents Contents Ethernet Line Card Product Numbers Router Hardware InstallationImportant Information Supported PlatformsLine Card Required Part Number Minimum IOS Software Release Hardware VersionRelated Documentation Product OverviewsMemory Options Ethernet Line Card ComparisonPort Gigabit Ethernet ISE Line Card Part NumberPort 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Safety Guidelines Preparing for InstallationPreventing Electrostatic Discharge Removing and Installing a Line Card Required Tools and EquipmentGuidelines for Line Card Removal and Installation Removing a Line CardLine Card Removal and Installation Installing a Line Card Ejector Levers Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line CardRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Removing and Installing GBICs Inserting the 2 screws on the Faceplate of the Line CardGeneral Gbic Handling and Maintenance Guidelines Removing the Gbic from an Ethernet Line CardInserting a Gbic into the Gigabit Ethernet Interface Removing and Replacing a GbicRemoving and Installing SFP Modules Bale Clasp SFP ModuleRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP ModuleRemoving a Mylar Tab SFP Module Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleActuator Button SFP Module Removing an Actuator Button SFP ModuleRemoving an Actuator Button SFP Module from a Port Installing an Actuator Button SFP Module Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Removing a Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Line Card Cable-Management BracketSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet InterfaceSC-Type Parameter RJ-45Parameter Gigabit Ethernet Interface Gbic Module Distance Connector Type Wavelength Fiber TypeGbic Laser Optical Transceiver Modules Power Sensitivity Budget Gbic Module Distance1 Connector Type Wavelength Fiber TypeTransmit Receive Link Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line Card Gbic Product Number Cwdm Gbic Wavelength Color IdentifierGeneral Cwdm Gbic Installation and Usage Guidelines Gigabit Ethernet SFP Modules Card carrier side of line cardTransceiver Budget Power Sensitivity Distance Power Transmit Receive Typical MaximumSFP Module Type Wavelength Cable Distance Gigabit Ethernet Fiber-Optic Interface CablesTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Removing and Installing Fiber-Optic Interface Cables Simplex LC Cable ConnectorRemoving Fiber-Optic Interface Cables Installing Fiber-Optic Interface Cables Disconnecting Line Card Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module Cleaning Fiber-Optic Connectors TX connector Simplex cables RX connector Duplex cableRemoving and Installing RJ-45 100BASE-T Copper Cable Type RJ-45 100BASE-T Copper CablesInstalling RJ-45 Cables Verifying and Troubleshooting the InstallationRemoving RJ-45 Cables Status LEDs Initial Boot ProcessGigabit Ethernet Status LEDs Alphanumeric LEDs Color/Activity DescriptionLED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Locations Line Card MemoryEthernet Line Card Hardware Engine Engine 2 Line Card Memory Locations ISE Line Card Memory LocationsISE Line Card Memory Locations Ethernet Line Card Route Memory Options Engine 4 Line Card Memory LocationsCisco Product Number Dimm Module Ethernet Line Card Packet Memory Options Removing and Installing Line Card MemoryCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Removing a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Installing a Sodimm Moving the Plastic Latch Away from the SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Completely Installed into Module Latch Electromagnetic Compatibility Regulatory Statements Regulatory, Compliance, and Safety Information Translated Safety Warnings and Agency Approvals FCC Class a ComplianceCanada Europe EUClass a Notice for Hungary Vcci Class a Notice for Japan Laser SafetyClass a Notice for Korea Obtaining Documentation and Submitting a Service Request OL-7861-01