Cisco Systems XR 12000 Series Installing a Slide Tab SFP Module, Removing a Slide Tab SFP Module

Page 36

Removing and Installing SFP Modules

Figure 28 Removing a Slide Tab SFP Module

	3
ACTIVE	CARRIER	RX PACKET

PASS	THRU
PASS	WRAP
	4OC48/SRP-
	SFP

84650

Step 6 Place the removed SFP module on an antistatic mat, or immediately place it in a static shielding bag if you plan to return it to the factory.

Step 7 Protect your line card by inserting clean SFP module cage covers into the optical module cage when there is no SFP module installed.

Installing a Slide Tab SFP Module

To install this type of SFP module into a line card, follow these steps:

Step 1 Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.

Step 2 Hold the SFP module with the hardware label facing up.

Caution The SFP module must be inserted with the hardware label facing up to avoiding damaging the module or the line card.

Step 3 Insert the SFP module into the appropriate slot and gently push on it until it snaps into the slot tightly. (See Figure 29.)

Cisco XR 12000 Series Router Ethernet Line Card Installation

36	OL-7861-01

Image 36

Contents Contents Router Hardware Installation Important InformationEthernet Line Card Product Numbers Supported PlatformsLine Card Required Part Number Minimum IOS Software Release Hardware VersionProduct Overviews Memory OptionsRelated Documentation Ethernet Line Card ComparisonPort Gigabit Ethernet ISE Line Card Part NumberPort 1-Gigabit Ethernet Line Card Link Active RX Frame Port 10-Gigabit Ethernet Line Card Preparing for Installation Safety GuidelinesPreventing Electrostatic Discharge Removing and Installing a Line Card Required Tools and EquipmentGuidelines for Line Card Removal and Installation Removing a Line CardLine Card Removal and Installation Installing a Line Card Ejector Levers Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line CardRemoving and Installing EPAs Inserting an EPA into a Modular Gigabit Ethernet Line Card Locations of Labels and Reference Points on the EPA Mating the Connector of the EPA to the Line Card Side Views Mating the Connector of the EPA to the Line Card Push Push Inserting and Tightening the Screw on the EPA Removing and Installing GBICs Inserting the 2 screws on the Faceplate of the Line CardGeneral Gbic Handling and Maintenance Guidelines Removing the Gbic from an Ethernet Line CardInserting a Gbic into the Gigabit Ethernet Interface Removing and Replacing a GbicRemoving and Installing SFP Modules Bale Clasp SFP ModuleRemoving a Bale Clasp SFP Module Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP ModuleRemoving a Mylar Tab SFP Module Mylar Tab SFP ModuleInstalling a Mylar Tab SFP Module Installing a Mylar Tab SFP ModuleActuator Button SFP Module Removing an Actuator Button SFP Module Removing an Actuator Button SFP Module from a Port Installing an Actuator Button SFP Module Slide Tab SFP ModuleRemoving a Slide Tab SFP Module Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Removing a Slide Tab SFP ModuleInstalling a Slide Tab SFP Module Line Card Cable-Management BracketSingle-Port Line Card Cable-Management Bracket Removing a Line Card Cable-Management Bracket 80220 Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet InterfaceParameter RJ-45 SC-TypeParameter Gbic Module Distance Connector Type Wavelength Fiber Type Gigabit Ethernet InterfaceGbic Laser Optical Transceiver Modules Gbic Module Distance1 Connector Type Wavelength Fiber Type Power Sensitivity BudgetTransmit Receive Link Using Cwdm GBICs with the 3-Port Gigabit Ethernet Line Card Gbic Product Number Cwdm Gbic Wavelength Color IdentifierGeneral Cwdm Gbic Installation and Usage Guidelines Gigabit Ethernet SFP Modules Card carrier side of line cardPower Transmit Receive Typical Maximum Transceiver Budget Power Sensitivity DistanceSFP Module Type Wavelength Cable Distance Fiber-Optic Interface Cables Gigabit EthernetTransceiver Option Type Wavelength SC cable connector Spring-action disconnect latch Removing and Installing Fiber-Optic Interface Cables Simplex LC Cable ConnectorRemoving Fiber-Optic Interface Cables Installing Fiber-Optic Interface Cables Disconnecting Line Card Interface CablesAttaching Simplex or Duplex Fiber Cables SFP Module Cleaning Fiber-Optic Connectors TX connector Simplex cables RX connector Duplex cableRemoving and Installing RJ-45 100BASE-T Copper Cable Type RJ-45 100BASE-T Copper CablesVerifying and Troubleshooting the Installation Installing RJ-45 CablesRemoving RJ-45 Cables Initial Boot Process Status LEDsGigabit Ethernet Status LEDs Alphanumeric LEDs Color/Activity DescriptionLED Display Meaning Source NnnnVget IOS Done Fabl Troubleshooting the Installation Line Card Memory Line Card Memory LocationsEthernet Line Card Hardware Engine Engine 2 Line Card Memory Locations ISE Line Card Memory LocationsISE Line Card Memory Locations Engine 4 Line Card Memory Locations Ethernet Line Card Route Memory OptionsCisco Product Number Dimm Module Removing and Installing Line Card Memory Ethernet Line Card Packet Memory OptionsCisco Product Number Dimm Modules Dimm Sockets Removing a Dimm Dimm Socket with Dual Release LeversInstalling a Dimm Removing a Sodimm Handling a DimmRemove Retaining Clip from Memory Module Socket Installing a Sodimm Moving the Plastic Latch Away from the SodimmSodimm Socket Retaining Clip Sodimm with Key in Face-up Position Inserting the Retaining Clip Checking the Installation of Line Card Memory Retaining Clip Completely Installed into Module LatchRegulatory, Compliance, and Safety Information Translated Safety Warnings and Agency ApprovalsElectromagnetic Compatibility Regulatory Statements FCC Class a ComplianceCanada Europe EUClass a Notice for Hungary Laser Safety Vcci Class a Notice for JapanClass a Notice for Korea Obtaining Documentation and Submitting a Service Request OL-7861-01