Cabletron Systems 6H259-17, 6H258-17 manual Connecting to the Network

Page 34

Connecting to the Network

To prevent damaging the backplane connectors in the following step, take care that the

!module slides in straight and properly engages the backplane connectors.

CAUTION

Ensure that the top plastic locking tab lines up with the desired slot number located on the front panel of the chassis. Refer to Figure 3-1.

6.Locate the slot guides that line up with the number of the slot in which the module will be installed. Install the module in the chassis by aligning the module circuit card between the upper and lower metal rail guides of the desired slot, sliding it into the chassis, and locking down the top and bottom plastic locking tabs, as shown in Figure 3-1. Take care that the module slides in straight and properly engages the backplane connectors.

7.If the chassis in which the module is installed was powered down for the installation, turn it back on. Check to see that the CPU LED settles at solid green after a few minutes. If the LED does not turn solid green, see Chapter 4 for details.

3.4CONNECTING TO THE NETWORK

This section provides the procedures for connecting segments from the network or other devices to the SmartSwitch.

NOTE

If the SmartSwitch is being installed in a network using SmartTrunking, there are rules concerning the network cable and port configurations that must be followed for SmartTrunking to operate properly. Before connecting the cables, refer to the Cabletron Systems SmartTrunk User’s Guide for the configuration information.

For the 6H258-17 and multimode fiber optic cable configuration information, refer to the Cabletron Systems Cabling Guide.

See Section 2.1 for information on connecting using single mode fiber optic cable with the 6H259-17.

3-4Installation

Page 33 Page 35
Image 34
Page 33 Page 35
Contents 9033381 Page Page FCC Notice Cabletron SYSTEMS, INC Program License Agreement Page Page Page Cabletron Systems Limited Program License Agreement Viii Class 1 Laser Transceivers Declaration of Conformity Contents Troubleshooting Figures Contents of SmartSwitch Shipping Container TablesUsing this Guide About This GuideStructure of this Guide Related Manuals Document Conventions Following conventions are used throughout this documentIntroduction OverviewCPU LED Connectivity Full Duplex Switched EthernetRuntime IP Address Discovery Broadcast Suppression SmartTrunkRemote Monitoring Rmon Port/VLAN Redirect FunctionsGarp Switch Operation Rate Limiting11 802.1 Port Priority Flow ControlManagement Optional HSIMs and VHSIMs Switching OptionsDistributed Chassis Management Standards CompatibilityYear 2000 Compliance Lanview Diagnostic LEDsGetting Help 100BASE-FX Network Network RequirementsMultimode Fiber Optic Cabling Single Mode Fiber Optic Cabling Installation Unpacking the SmartswitchInstalling Options Installing the Smartswitch Into the 6C105 ChassisInstalling an Interface Module Connecting to the Network Connecting to the NetworkConnecting a Fiber Optic Segment to the SmartSwitch Completing the Installation Troubleshooting Using LanviewReceive LED Transmit LED CPU Refer to your Local Management Troubleshooting Checklist Power System Troubleshooting Refer to your Local Management User’s Guide for proper Refer to your Local Management User’s Guide for IP Device Setup Troubleshooting Using the Reset Button 6H258-17Module Specifications SpecificationsPhysical Properties INPUT/OUTPUT Ports Environmental RequirementsCOM Port Pinout Assignments Regulatory Compliance Options for both the 6H258-17 and the 6H259-17Page Switch Settings, Upgrades, and Installations Setting the Mode SwitchesFigure B-1 Module Mode Switch Location/Component Layout Simm Upgrade Locating SIMMsInstalling the Dram Simm Figure B-2 Simm Slot LocationsInstalling Optional High Speed Interface Modules Figure B-3 Installing the DramDram Index NumericsIndex-2

6H259-17, 6H258-17 specifications

Cabletron Systems, a pioneer in computer networking and telecommunications, has consistently delivered innovative solutions tailored to meet the evolving demands of network infrastructure. Among its notable offerings are the models 6H258-17 and 6H259-17, which showcase advanced technological features designed to optimize network performance, reliability, and scalability.

The 6H258-17 stands out as a high-performance network switch, boasting 24 Ethernet ports, facilitating efficient data transfer and connectivity among multiple devices. Its architecture supports both 10BASE-T and 100BASE-TX Ethernet standards, providing flexibility in deploying a variety of network configurations. The switch also employs innovative packet-switching technology, ensuring low-latency communication and enhanced throughput, which is critical for bandwidth-intensive applications.

On the other hand, the 6H259-17 acts as a versatile router and works seamlessly with the 6H258-17 switch, creating a cohesive networking solution. This model is equipped with a robust routing protocol suite, including RIP and OSPF, to facilitate intelligent data routing across networks. Its ability to accommodate various WAN interfaces further enhances its adaptability in different networking environments, making it suitable for both small businesses and larger enterprise setups.

One of the key characteristics of both models is their modular design, which allows for easy upgrades and expansions as the networking requirements grow. Users can invest in additional modules or line cards, enabling them to scale their systems without the need for complete replacements. This feature not only extends the lifespan of the equipment but also aligns with cost-effective budgeting strategies.

In terms of security, Cabletron Systems has integrated sophisticated features into both products to safeguard data integrity and prevent unauthorized access. The ability to implement VLANs and access control lists ensures that only authorized users can access sensitive information. This focus on security is paramount in today’s landscape, where data breaches pose significant risks to organizations of all sizes.

Additionally, both the 6H258-17 and 6H259-17 are designed for easy management and monitoring. With a user-friendly interface and support for SNMP, network administrators can efficiently oversee network activities, troubleshoot issues, and optimize performance.

In conclusion, the Cabletron Systems 6H258-17 and 6H259-17 represent powerful networking solutions that combine performance, scalability, security, and ease of management. Their advanced technologies make them a valuable choice for organizations looking to enhance their network infrastructure while ensuring future growth and adaptability.
Top Page Image Contents