Cabletron Systems TRFMIM-28 Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way

Page 3

Notice

Notice

Cabletron Systems reserves the right to make changes in speciﬁcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

© Copyright March 1998 by:

Cabletron Systems, Inc.

35 Industrial Way

Rochester, NH 03867-5005

All Rights Reserved

Printed in the United States of America

Order Number: 9032061-01

LANVIEW is a registered trademark, and SmartSwitch is a trademark of Cabletron Systems, Inc. CompuServe is a registered trademark of CompuServe, Inc.

i960 microprocessor is a registered trademark of Intel Corp.

Ethernet is a trademark of Xerox Corporation.

i

Image 3

Contents 9032061-01 SmartSwitch 9H423-28 User’s GuidePage Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way FCC Notice VCCI NoticeDOC Notice DECLARATION OF CONFORMITY ADDENDUM Nexus House, Newbury Business ParkConformance to Directives/Product Standards Safety Information CLASS 1 LASER TRANSCEIVERSThe FPIM-05 and FPIM-07 are Class 1 Laser Products CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Introduction ContentsInstalling the 9H423-28 Module ChapterSpeciﬁcations Contentsviii Chapter IntroductionManagement FeaturesFast Packet Switching ProcessorThe 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs SMB CPU INB FAST ENET Figure 1-1. The 9H423-28 Module26X 25X FAST ENET 9H423-28Getting Help Related ManualsInstalling the 9H423-28 Module Installing an FEPIMUnpacking the Module User Accessible Components Setting the Module DIP Switch See the Cautions at the end of this table Table 2-1. Function of DIP SwitchInstalling the Module in the SmartSwitch 9000 Chassis Module Figure 2-3. Installing the ModulePlastic Tab Jack for ESD Wrist Strap Metal Back-PanelReset Switch The Reset SwitchInstalling the 9H423-28 Module Operation Operation ENIB/FENIBSmartSwitch ASIC Traditional SwitchVLAN VLAN Domains Fully-Meshed VLAN Domains SecureFast VLAN SwitchesSMB-1 Bus i960 CoreINB NIB System Management BusesSMB-10 Bus System Diagnostic ControllerDC/DC Converter INB InterfaceLowest Slot Number Level ITDM Arbitration LevelsITDM RAM Allocation Level Round Robin Arbitration LevelMonarch/Slave SmartSwitch 9000 Modules 3-10 System Status INB Transmit Port Receive LANVIEW LEDsINB Receive Port TransmitThe function of the INB Receive LEDs is listed in Table The function of the INB Transmit LEDs is listed in TableLANVIEW LEDs Table 4-5. Port Transmit LEDs The function of the Port Receive LEDs is listed in TableThe function of the Port Transmit LEDs is listed in Table Table 4-4. Port Receive LEDsLANVIEW LEDs Standards SpeciﬁcationsTechnical Speciﬁcations MemoryWeight SafetyService DimensionsStorage Temperature EnvironmentOperating Temperature 5 to 40 CSpeciﬁcations Appendix A FEPIM SpeciﬁcationsFE-100TX FE-100FXFEPIM Speciﬁcations FE-100FX