Cabletron Systems TRFMIM-28 manual FEPIM Speciﬁcations, FE-100TX, FE-100FX, Appendix A

Page 43

Appendix A

Appendix A

FEPIM Speciﬁcations

The 9H423-28 SmartSwitch 9000 module uses a Fast Ethernet Interface Module (FEPIM) to provide front panel cable connections. FEPIMs are user-installable. See the section titled Installing an FEPIM in Chapter 2.

FE-100TX

The FE-100TX is an RJ45 connector supporting Unshielded Twisted Pair (UTP) cabling.

The slide switch on the FE-100TX determines the crossover status of the cable pairs. If the switch is on the X side, the pairs are internally crossed over. If the switch is on the = side, the pairs are not internally crossed over. Figure A-1 shows the pinouts for the FEPIM-100TX in both positions.

Position =

(not crossed over)

1. TX+ 5. NC

2. TX- 6. RX-

3.RX+ 7. NC

4.NC 8. NC

=

x

10

100

FE-100TX

166505

Position X (crossed over)

1.RX+ 5. NC

2.RX- 6. TX-

3.TX+ 7. NC

4.NC 8. NC

Figure A-1. FE-100TX Pinouts

FE-100FX

The FE-100FX shown in Figure A-2 supports multimode ﬁber optic cabling. The FE-100FX is equipped with an SC-style port. Table A-1 lists the speciﬁcations for the FE-100FX.

A-1

Image 43

Contents 9032061-01 SmartSwitch 9H423-28 User’s GuidePage Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way VCCI Notice FCC NoticeDOC Notice Nexus House, Newbury Business Park DECLARATION OF CONFORMITY ADDENDUMConformance to Directives/Product Standards CLASS 1 LASER TRANSCEIVERS Safety InformationThe FPIM-05 and FPIM-07 are Class 1 Laser Products CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Introduction ContentsInstalling the 9H423-28 Module ChapterContents Speciﬁcationsviii Chapter IntroductionManagement FeaturesFast Packet Switching ProcessorThe 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs SMB CPU INB FAST ENET Figure 1-1. The 9H423-28 Module26X 25X FAST ENET 9H423-28Getting Help Related ManualsInstalling an FEPIM Installing the 9H423-28 ModuleUnpacking the Module User Accessible Components Setting the Module DIP Switch See the Cautions at the end of this table Table 2-1. Function of DIP SwitchInstalling the Module in the SmartSwitch 9000 Chassis Module Figure 2-3. Installing the ModulePlastic Tab Jack for ESD Wrist Strap Metal Back-PanelReset Switch The Reset SwitchInstalling the 9H423-28 Module Operation Operation ENIB/FENIBTraditional Switch SmartSwitch ASICVLAN VLAN Domains Fully-Meshed VLAN Domains SecureFast VLAN SwitchesSMB-1 Bus i960 CoreINB NIB System Management BusesSMB-10 Bus System Diagnostic ControllerDC/DC Converter INB InterfaceLowest Slot Number Level ITDM Arbitration LevelsITDM RAM Allocation Level Round Robin Arbitration LevelMonarch/Slave SmartSwitch 9000 Modules 3-10 System Status INB Transmit Port Receive LANVIEW LEDsINB Receive Port TransmitThe function of the INB Transmit LEDs is listed in Table The function of the INB Receive LEDs is listed in TableLANVIEW LEDs Table 4-5. Port Transmit LEDs The function of the Port Receive LEDs is listed in TableThe function of the Port Transmit LEDs is listed in Table Table 4-4. Port Receive LEDsLANVIEW LEDs Standards SpeciﬁcationsTechnical Speciﬁcations MemoryWeight SafetyService DimensionsStorage Temperature EnvironmentOperating Temperature 5 to 40 CSpeciﬁcations Appendix A FEPIM SpeciﬁcationsFE-100TX FE-100FXFEPIM Speciﬁcations FE-100FX