Cabletron Systems TRFMIM-28 manual Installing the Module in the SmartSwitch 9000 Chassis

Page 21

Installing the 9H423-28 Module

Installing the Module in the SmartSwitch 9000 Chassis

To install the 9H423-28 module in the SmartSwitch 9000 chassis, follow the steps below:

1.Remove the blank panel covering the slot in which the module will be mounted. All other slots must be covered to ensure proper air ﬂow and cooling.

2.Attach one end of the ESD wrist strap (packaged with the SmartSwitch 9000 chassis) to your wrist. Plug the other end into the jack for the ESD Wrist Strap in the lower right corner of the SmartSwitch 9000 chassis shown in Figure 2-3.

3.Install the module in the chassis by sliding it into slots and locking down both the top and bottom plastic tabs, as shown in Figure 2-3. Take care that the module is between the card guides as shown, it slides in straight, and engages the backplane connectors properly.

2-5

Image 21

Contents 9032061-01 SmartSwitch 9H423-28 User’s GuidePage Copyright March 1998 by Cabletron Systems, Inc 35 Industrial Way FCC Notice VCCI NoticeDOC Notice DECLARATION OF CONFORMITY ADDENDUM Nexus House, Newbury Business ParkConformance to Directives/Product Standards Safety Information CLASS 1 LASER TRANSCEIVERSThe FPIM-05 and FPIM-07 are Class 1 Laser Products CLASS 1 LASER TRANSCEIVERS Laser Radiation and Connectors Page Installing the 9H423-28 Module ContentsChapter IntroductionSpeciﬁcations Contentsviii Chapter IntroductionFast Packet Switching FeaturesProcessor ManagementThe 9H423-28 module provides MIB support including RMON RFC-1271 LANVIEW LEDs 26X 25X Figure 1-1. The 9H423-28 ModuleFAST ENET 9H423-28 SMB CPU INB FAST ENETGetting Help Related ManualsInstalling the 9H423-28 Module Installing an FEPIMUnpacking the Module User Accessible Components Setting the Module DIP Switch See the Cautions at the end of this table Table 2-1. Function of DIP SwitchInstalling the Module in the SmartSwitch 9000 Chassis Plastic Tab Jack for ESD Wrist Strap Figure 2-3. Installing the ModuleMetal Back-Panel ModuleReset Switch The Reset SwitchInstalling the 9H423-28 Module Operation Operation ENIB/FENIBSmartSwitch ASIC Traditional SwitchVLAN VLAN Domains Fully-Meshed VLAN Domains SecureFast VLAN SwitchesINB NIB i960 CoreSystem Management Buses SMB-1 BusDC/DC Converter System Diagnostic ControllerINB Interface SMB-10 BusITDM RAM Allocation Level ITDM Arbitration LevelsRound Robin Arbitration Level Lowest Slot Number LevelMonarch/Slave SmartSwitch 9000 Modules 3-10 INB Receive LANVIEW LEDsPort Transmit System Status INB Transmit Port ReceiveThe function of the INB Receive LEDs is listed in Table The function of the INB Transmit LEDs is listed in TableLANVIEW LEDs The function of the Port Transmit LEDs is listed in Table The function of the Port Receive LEDs is listed in TableTable 4-4. Port Receive LEDs Table 4-5. Port Transmit LEDsLANVIEW LEDs Technical Speciﬁcations SpeciﬁcationsMemory StandardsService SafetyDimensions WeightOperating Temperature Environment5 to 40 C Storage TemperatureSpeciﬁcations FE-100TX FEPIM SpeciﬁcationsFE-100FX Appendix AFEPIM Speciﬁcations FE-100FX