Cabletron Systems manual BRIM-A6 Specifications, Related Manuals, Emi, Emc

Page 12

Chapter 1: Introduction

1.5 BRIM-A6 SPECIFICATIONS

This section describes environment speciﬁcations and safety requirements for the BRIM-A6. Cabletron Systems reserves the right to change these speciﬁcations at any time without notice.

Environment	5°C to 40°C (41°F to 104°F)
Operating Temperature:	5°C to 40°C (41°F to 104°F)
Storage Temperature:	-30°C to 90°C (-22°F to 194°F)
Operating Humidity:	5% to 95% (non-condensing)

Safety

This unit meets the safety requirements of UL1950, CSA C22.2 No. 950, and EN60950.

EMI

This unit meets the EMI requirements of FCC Part 15 Class A, EN55022 Class A and VCCI Class I.

EMC

This unit meets the EMC requirements of EN 50082-1 including: IEC 801-2 (ESD), IEC 801-3 (Radiated Susceptibility), and IEC 801-4 (EFT/B).

1.6 RELATED MANUALS

Use the following manuals to supplement the procedures and other technical data provided in this manual. This manual references procedures in these manuals, where appropriate, but does not repeat them.

Cabletron Systems EMM-E6 User’s Guide

Cabletron Systems ESXMIM Installation Guide

Cabletron Systems MicroMMAC User’s Guide

Cabletron Systems NBR-620/420/220 Installation Guide and NBR-620/420/220 Local Management Guide

Page 1-4

BRIM-A6 User’s Guide

Image 12

Contents BRIM-A6 USER’S Guide BRIM-A6 User’s Guide FCC Notice DOC NoticeVcci Notice Exclusion of Warranty and Disclaimer of Liability Cabletron SYSTEMS, INC. Program License AgreementCabletron Software Program License United States Government Restricted Rights Declaration of Conformity Contents Viii BRIM-A6 User’s Guide Using this Manual Chapter IntroductionDocument Conventions Following conventions are used throughout this documentBRIM-A6 Features BRIM-A6 OverviewBRIM-A6 Specifications Related ManualsEMI EMCGetting Help Chapter Installation Unpacking the BrimInstalling Apims Installing an ApimInstalling Brims Installing a Brim in a MIMRemoving the Brim Coverplate Installing a Brim in a Hub BRIM-A6 User’s Guide Chapter Local Management Local Management Keyboard Conventions Keyboard Conventions FunctionUsing LIM to Create PVCs ATM Connection Tables ScreenATM Connection Tables Screen Fields ATM Connection Tables Screen Commands Using ATM Connection Tables Screen CommandsAdding PVCs to the Connection Tables Screen Deleting PVCs from the Connection Tables ScreenUsing LM to Create Pvcs BRIM-A6 Setup ScreenBRIM-A6 Setup Screen Fields VPIVCI BRIM-A6 Setup Screen Commands Using BRIM-A6 Setup Screen Commands Accessing the BRIM-A6 Add/Delete Entry ScreenBRIM-A6 Add/Delete Entry Screen Fields BRIM-A6 Add/Delete Entry Screen Commands Adding a PVCModifying a PVC Deleting a PVC Chapter BRIM-A6 LEDsApim LEDs Describes each of the Apim LEDsAppendix a Apim Specifications APIM-11 SpecificationsAPIM-21 Specifications APIM-22 Specifications APIM-29 SpecificationsAPIM-67 Specifications BNCAppendix B ATM Overview ATM BasicsATM Cell Figure B-1 ATM CellsBRIM-A6 User’s Guide B-3 ATM Network Virtual Channels and Virtual PathsPermanent and Switched Virtual Channels ATM ProtocolB-6 BRIM-A6 User’s Guide BRIM-A6 User’s Guide B-7 B-8 BRIM-A6 User’s Guide