Cabletron Systems manual Removing the 7H02-06 Module from a 7C04 or 7C04-R Chassis

Page 26

Installation

3.3.4Removing the 7H02-06 Module from a 7C04 or 7C04-R Chassis

To remove the 7H02-06 Module from a 7C04 or 7C04-R Chassis, follow the listed steps and refer to Figure 3-7 and Figure 3-8 respectively.

Note: Before removing the 7H02-06Module, attach the wrist strap included with the module (instructions are printed on the packet).

1.Use a slotted screwdriver to loosen the two screws that secure the module to the chassis.

2.Locate the two ejector tabs on the module (below the screws on the left and right ends of the module).

3.Simultaneously press left on the left ejector tab and press right on the right ejector tab until the module ejects from the backplane.

4.Grasp both ejector tabs and carefully slide the module out of the chassis.

Screws

FANS

Ejector Tabs

Figure 3-7. Removing the 7H02-06 Module from the 7C04 Workgroup

SmartSwitch

3-8

Image 26

Contents 9031924 Page Page FCC Notice Vcci Notice Exclusion of Warranty Disclaimer of Liability Contents Appendix a Using this Manual Chapter Introduction7H02-06 Module Cable Type and FEPIMsH02-06 Module Features Lanview LEDsConnectivity FEPIMsFE-100TX Related Manuals Getting HelpFE-100FX Fepim Module SpecificationsChapter Network Requirements Transmitter power parameters are listed in Table FE-100TX and Fixed RJ45 PortsPin Number Represents Network Requirements Unpacking the 7H02-06 Module Chapter InstallationInstalling Fepims Ejector Tab Screws INSTALLING/REMOVING the 7H02-06 Module Installing the 7H02-06 Module in a 7C03 Mmac SmartSwitchInstalling the 7H02-06 Module 7C03 Mmac SmartSwitch Removing the 7H02-06 Module from a 7C03 Mmac SmartSwitch Removing the 7H02-06 Module from a 7C03 Mmac SmartSwitchInstalling the 7H02-06 Module in a 7C04 or 7C04-R Chassis Power Removing the 7H02-06 Module from a 7C04 or 7C04-R Chassis XXX Installation Chapter Troubleshooting Shows the Lanview LEDs of the 7H02-06 ModuleIndicates the state of the receive port System Resources Chapter Technical SpecificationsSafety StandardsNetwork Interfaces ServiceImmunity PhysicalEnvironmental Technical Speciﬁcations Figure A-1.FE-100TX Pinouts Cable Type Worst Case Budget Typical Budget

7H02-06 specifications

Cabletron Systems, a pioneer in the networking and telecommunications industry, has produced the 7H02-06 model, a versatile and efficient network interface card (NIC) designed to enhance network performance and reliability. This advanced NIC is particularly well-suited for businesses seeking to optimize their data communication infrastructure.

One of the standout features of the Cabletron Systems 7H02-06 is its robust support for multiple network standards, enabling seamless integration into various network environments. The card is compatible with both Ethernet and Fast Ethernet, allowing users to harness the speed benefits of Fast Ethernet while maintaining backward compatibility with existing Ethernet installations. This feature significantly reduces the costs associated with upgrading network infrastructure.

The 7H02-06 also incorporates advanced technologies that enhance data transmission efficiency. It supports full-duplex operation, which allows for simultaneous sending and receiving of data. This capability effectively doubles the potential bandwidth of the network link, resulting in faster data transfer rates and improved overall performance.

In terms of characteristics, the Cabletron Systems 7H02-06 is designed with robust error-checking mechanisms, ensuring data integrity during transmission. The NIC utilizes sophisticated algorithms to detect and correct errors, which is critical for maintaining high levels of reliability in data communication.

Another key aspect of the 7H02-06 is its flexibility in network configuration. The card is equipped with multiple interface options, including the ability to connect to both coaxial and twisted-pair cabling. This versatility enables network administrators to tailor the card’s functionality to fit their specific network architecture, facilitating easier upgrades and expansions.

Moreover, the Cabletron Systems 7H02-06 is backed by a comprehensive suite of management tools, allowing organizations to monitor network performance, troubleshoot issues, and optimize configurations proactively. This level of control empowers IT teams to maintain a stable and efficient networking environment over time.

In conclusion, the Cabletron Systems 7H02-06 represents a significant advancement in network interface technology, integrating multiple standards, enhancing data transmission capabilities, and supporting flexible configurations. These features make it an ideal choice for businesses aiming to modernize their networking infrastructure while maximizing performance and reliability.