EMC QLogic manual Configuring the HBA, Boot Bios

Page 59

Configuring an EMC Boot Device

3. To disconnect all SCSI hard disk drives, unplug the power and SCSI bus cables connected to a SCSI adapter or controller. For details, see the installation and operation manual for your server.

4. To prepare your system to boot Windows over a Fibre Channel connection, you must do the following:

For detailed installation instructions on the HP ProLiant BL20p G2 and BL40p, refer to HP ProLiant BL p-Class server blades Booting Windows systems from 3 rd party Storage Array Network (SAN), How To, located here:

ftp://ftp.compaq.com/pub/supportinformation/techpubs /other/5982-3248en_rev1_us.pdf

Following this installation proceed to Verifying HBA Driver and Digital Signature Installation on page 3-28. For other detailed instructions, refer to the manufacturer’s documentation available for each adapter.

• For any server with IDE CD-ROM drives, you should disable BIOS on any of the server’s integrated SCSI adapter(s) because SCSI BIOS is not required to boot from CD-ROM.

• Disable or remove any IDE HDD drives.

• For servers with SCSI CD-ROM drives, enable BIOS on the

 

 

SCSI channel that includes the CD-ROM; disable BIOS on any

 

 

 

other integrated SCSI channels. Remove any SCSI hard disks

 

 

 

on the same bus as the CD-ROM drive.

 

 

 

 

 

 

 

 

If the CD-ROM is on a SCSI controller and the BIOS is disabled for

 

 

 

that controller, then you will not be able to boot from the CD-ROM.

 

 

 

To boot from CD-ROM in the future, you will need to re-enable the

 

 

 

BIOS for the CD-ROM controller.

 

 

 

 

 

 

 

• Disable BIOS on any other HBA BIOS in your system other

 

 

 

than the QLogic HBA(s) designated for booting. See the

 

 

 

documentation that accompanied the HBA for instructions.

 

What Next?

Configure the HBA Boot BIOS as described in the next section.

 

 

 

 

 

 

Configuring the HBA

Follow these steps to configure the storage system LUN for the HBA

 

Boot BIOS

Boot BIOS:

 

 

1. Reboot the server.

 

 

When the QLogic BIOS banner (shown below) appears, press

 

 

CTRL–Q.

 

 

 

 

 

 

 

 

Configuring a CLARiiON Boot Device

3-23

 

 

 

 

 

3

Image 59
Contents REV A07 Trademark Information Copyright 2001-2005 EMC Corporation. All rights reservedContents Chapter Configuring an EMC Boot Device Appendix a Third-Party Software Chapter Installing and Configuring the QLogic QLA4010 iSCSIAppendix B Troubleshooting Problem Index Hardware or software EMC uses the following conventions for notes, cautions,Damage to the system or equipment. The caution may apply to Bold Related Documentation Typographical ConventionsPalatino Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Downloading QLogic Drivers Firmware Verifying Documentation IntroductionInstalling an HBA Check for an Updated HBA Driver Move the jumpers, onto pins 1-2 if not already there Reconfigure the HBA JumperSet the HBA FC-AL Loop ID Installing an HBA Settings menus EMC HBA SettingsPre-Configured SettingsConfiguring Nvram for Stratus ftServers QLogic HBAs Firmware/BIOSFibre-Down Servers With EmbeddedUpdating While Running Windows Press the Down Arrow until you select Data Rate then press EMC HBA Settings Driver Revision History Where to Find the Driver Installing the HBA DriverSelect have Disk Windows 2003 STORPort UpdatesExtended Error Logging by QLogic Drivers Installation Procedure for Windows NT HostsAdministrative Tools, Computer Management Installing the HBA Driver Double-click the Scsi & RAID Controllers icon Installing and Configuring the HBA Driver Upgrading to Windows 2003 from Windows 2000 or Windows NT Replacing an HBA Arrays with Device Masking EnabledEMC Symmetrix Powermt restore powermt display Installing and Configuring the HBA Driver Configuring an EMC Boot Device Risks of Booting from the Storage Array Boot-from-SAN Configuration RestrictionsHow to Determine I/O Latency and Load on the Boot LUN Boot-from-SAN with Mscs Boot Crashdump Save to Disk BehaviorConfiguring the Boot Bios Configuring a Symmetrix Boot DeviceConfiguration Settings menu From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter Select Current Boot Node Name and press EnterInstalling the Windows OS onto the Boot Device Installing EFI boot code onto the HBA Unload 5D Configuring an EMC Boot Device Configurable Components Drv5DCtrl60Langeng Configuring an EMC Boot Device Configuring a Symmetrix Boot Device Flowchart Configuring a CLARiiON Boot DeviceProcedure Configuring a CLARiiON Boot Device Topologies Configurations, Revisions Hardware Software RequirementsRequirements Refer to Downloading QLogic Drivers and Firmware on Preparing the Storage SystemSetting Up the HBA Bios Preparing the Fabric Configuring an EMC Boot Device What Next? Node NamePreparing the Server Boot Bios Configuring the HBAConfiguring an EMC Boot Device When the QLogic Bios banner shown in appears, press Windows Licensing Agreement appears Configuring a CLARiiON Boot Device Verifying HBA Driver and Digital Signature Installation What Next? From here Assigning a Permanent Boot Drive Letter for Windows NTInstalling Multipath and Failover Software Installing Additional Navisphere Host Agent Software Storagegroupname y/n? Configuring an EMC Boot Device On the Computer Management window, click Disk Management Trespassing the Boot LUN Using atftrespassStarting a Fresh Installation Boot Time and LUN AvailabilityBoot Time and LUN Availability EMC Symmetrix EMC CLARiiON Replacing a Boot HBAExplanations of Entries How a Server Responds to Failure in the Boot LUN PathNtosknl Bsod Known IssuesHBA TOE Windows 2003 STORPort Updates Next dialog, click ReInstall Driver, and then, click Next Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Configuring iSNS settings for QLA4010 Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Installing Boot Bios on the QLA4010 iSCSI HBA from DOS Select iSCSI Boot Settings Select Configuration Settings from the menuSelect iSCSI Boot Settings, and press Enter Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Third-Party Software QLogic SANSurfer SANBlade Manager SANSurfer versions include Initial Release SANSurfer Version HistoryVeritas Volume Manager Veritas Volume Manager 3.x for WindowsVeritas Foundation Suite Veritas Volume Manager 3.1 and Veritas DMPThird-Party Software Troubleshooting Solution Problems and SolutionsProblem Later already contain this correction Flasutil Index Nvram

QLogic specifications

EMC QLogic is a leading provider of advanced networking solutions, primarily known for its high-performance storage area network (SAN) technologies. It specializes in Fibre Channel and Ethernet networking products, offering robust solutions that are essential for modern data center environments.

One of the key features of EMC QLogic is its exceptional performance in high-speed data transfer. QLogic's Fibre Channel products, such as switches and host bus adapters (HBAs), support speeds of up to 32 Gbps, ensuring ultra-fast communication between storage devices and servers. This high throughput is crucial for applications demanding high IOPS (Input/Output Operations Per Second), particularly in virtualized environments and databases.

Another prominent aspect of EMC QLogic's technology is its support for advanced features like Data Center Bridging (DCB). DCB enables the convergence of storage and traditional Ethernet traffic on a single network, streamlining data center management and reducing costs. By allowing both storage and data networking to coexist on the same infrastructure, EMC QLogic enhances efficiency and simplifies network architecture.

Scalability is another characteristic that sets EMC QLogic apart. The architecture is designed to support a wide range of deployment sizes, from small businesses to large enterprise data centers. This scalability ensures that organizations can grow their IT infrastructure without needing to overhaul their existing deployment.

EMC QLogic also places a strong emphasis on reliability and security. Their products are built with redundancy and failover mechanisms, which minimize downtime and ensure continuous operation even in the event of hardware failure. Additionally, security features such as encryption and access controls are integrated to protect sensitive data as it travels across the network.

Management and monitoring capabilities are also integral to EMC QLogic's offerings. The company provides advanced software tools for managing network resources, allowing administrators to monitor performance, diagnose issues, and optimize configurations efficiently. This helps organizations maintain peak performance and reduces operational complexity.

In summary, EMC QLogic combines high-speed performance, advanced features, and robust reliability in its networking solutions. With a focus on scalability and security, it provides organizations with the tools necessary to build and manage efficient, modern data centers that can adapt to evolving technological demands. Its commitment to innovation positions EMC QLogic as a trusted partner in the storage networking landscape.