Contents
REV A07
Trademark Information
Copyright 2001-2005 EMC Corporation. All rights reserved
Contents
Chapter Configuring an EMC Boot Device
Appendix B Troubleshooting
Chapter Installing and Configuring the QLogic QLA4010 iSCSI
Appendix a Third-Party Software
Problem Index
Damage to the system or equipment. The caution may apply to
EMC uses the following conventions for notes, cautions,
Hardware or software
Palatino
Related Documentation Typographical Conventions
Bold
Introduction
Understanding Persistent Binding in a Fabric Environment
Understanding Persistent Binding in a Fabric Environment
HBA
Installing Configuring the HBA Driver
Downloading QLogic Drivers Firmware Verifying Documentation
Introduction
Installing an HBA
Check for an Updated HBA Driver
Move the jumpers, onto pins 1-2 if not already there
Reconfigure the HBA Jumper
Set the HBA FC-AL Loop ID
Installing an HBA
Pre-Configured
EMC HBA Settings
Settings
Settings menus
Configuring Nvram for Stratus ftServers
Fibre-Down Servers
Firmware/BIOS
With Embedded
QLogic HBAs
Updating While Running Windows
Press the Down Arrow until you select Data Rate then press
EMC HBA Settings
Driver Revision History Where to Find the Driver
Installing the HBA Driver
Extended Error Logging by QLogic Drivers
Windows 2003 STORPort Updates
Installation Procedure for Windows NT Hosts
Select have Disk
Administrative Tools, Computer Management
Installing the HBA Driver
Double-click the Scsi & RAID Controllers icon
Installing and Configuring the HBA Driver
Upgrading to Windows 2003 from Windows 2000 or Windows NT
Replacing an HBA
EMC Symmetrix
Masking Enabled
Arrays with Device
Powermt restore powermt display
Installing and Configuring the HBA Driver
Configuring an EMC Boot Device
Risks of Booting from the Storage Array
Boot-from-SAN Configuration Restrictions
How to Determine I/O Latency and Load on the Boot LUN
Boot-from-SAN with Mscs
Boot Crashdump Save to Disk Behavior
Configuring the Boot Bios
Configuring a Symmetrix Boot Device
From the Host Adapter Settings menu, select Host Adapter
From the Configuration Settings menu, select Host Adapter
Select Current Boot Node Name and press Enter
Configuration Settings menu
Installing the Windows OS onto the Boot Device
Installing EFI boot code onto the HBA
Unload 5D
Configuring an EMC Boot Device
Configurable Components Drv5DCtrl60Langeng
Configuring an EMC Boot Device
Configuring a Symmetrix Boot Device
Procedure
Configuring a CLARiiON Boot Device
Flowchart
Configuring a CLARiiON Boot Device
Requirements
Configurations, Revisions Hardware Software Requirements
Topologies
Refer to Downloading QLogic Drivers and Firmware on
Preparing the Storage System
Setting Up the HBA Bios
Preparing the Fabric
Configuring an EMC Boot Device
What Next?
Node Name
Preparing the Server
Boot Bios
Configuring the HBA
Configuring an EMC Boot Device
When the QLogic Bios banner shown in appears, press
Windows Licensing Agreement appears
Configuring a CLARiiON Boot Device
Verifying HBA Driver and Digital Signature Installation
Installing Multipath and Failover Software
Assigning a Permanent Boot Drive Letter for Windows NT
What Next? From here
Installing Additional Navisphere Host Agent Software
Storagegroupname y/n?
Configuring an EMC Boot Device
On the Computer Management window, click Disk Management
Trespassing the Boot LUN Using atftrespass
Starting a Fresh Installation
Boot Time and LUN Availability
Boot Time and LUN Availability
EMC Symmetrix EMC CLARiiON
Replacing a Boot HBA
Explanations of Entries
How a Server Responds to Failure in the Boot LUN Path
Ntosknl Bsod
Known Issues
HBA TOE
Windows 2003 STORPort Updates
Next dialog, click ReInstall Driver, and then, click Next
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Configuring iSNS settings for QLA4010
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Installing Boot Bios on the QLA4010 iSCSI HBA from DOS
Select iSCSI Boot Settings
Select Configuration Settings from the menu
Select iSCSI Boot Settings, and press Enter
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Third-Party Software
QLogic SANSurfer SANBlade Manager
SANSurfer versions include Initial Release
SANSurfer Version History
Veritas Volume Manager
Veritas Volume Manager 3.x for Windows
Veritas Foundation Suite
Veritas Volume Manager 3.1 and Veritas DMP
Third-Party Software
Troubleshooting
Problem
Problems and Solutions
Solution
Later already contain this correction
Flasutil
Index
Nvram