EMC manual Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE

Page 91

Installing and Configuring the QLogic QLA4010 iSCSI HBA (TOE)

From this point, press S to specify additional devices. You will need to select Other and press ENTER.

3.Insert the diskette with the QLogic driver into the diskette drive, and press ENTER.

4.Select the driver by pressing ENTER. The driver loads and you are brought back to the Additional Devices dialog.

5.If you want to specify drivers for other devices installed in your system, do so; otherwise press ENTER at the Additional Devices dialog to continue with Windows installation.

6.Continue the installation procedure as though you were installing to an internal hard disk. Choose the correct boot disk for your iSCSI HBA from the list of discovered LUNs.

Windows 2000 For detailed installation instructions on the HP ProLiant BL20p G2 and BL40p, refer to HP ProLiant BL p-Class server blades Booting Win- dows systems from 3rd party Storage Array Network (SAN), How To, located here:

ftp://ftp.compaq.com/pub/supportinformation/techpubs/ other/5982-3248en_rev1_us.pdf

After completing Windows installation, reinstall the QLogic driver

using the steps under Installation Procedure for Windows 2000 and Win- dows 2003 Hosts on page 2-16.

NOTE: For Windows 2003 installations using the QLogic STORPort driver, it will be necessary to install the latest supported Microsoft STORPort hotfix (QFE). Refer to the EMC Support Matrix for the current hotfix version.

Installing and Configuring the QLA4010 iSCSI HBA to boot from an EMC Storage Array

4-17

 

 

4

Image 91
Contents REV A07 Trademark Information Copyright 2001-2005 EMC Corporation. All rights reservedContents Chapter Configuring an EMC Boot Device Appendix B Troubleshooting Chapter Installing and Configuring the QLogic QLA4010 iSCSIAppendix a Third-Party Software Problem Index Damage to the system or equipment. The caution may apply to EMC uses the following conventions for notes, cautions,Hardware or software Palatino Related Documentation Typographical ConventionsBold Introduction Understanding Persistent Binding in a Fabric Environment Understanding Persistent Binding in a Fabric Environment HBA Installing Configuring the HBA Driver Downloading QLogic Drivers Firmware Verifying Documentation IntroductionInstalling an HBA Check for an Updated HBA Driver Move the jumpers, onto pins 1-2 if not already there Reconfigure the HBA JumperSet the HBA FC-AL Loop ID Installing an HBA Settings menus EMC HBA SettingsPre-Configured SettingsConfiguring Nvram for Stratus ftServers QLogic HBAs Firmware/BIOSFibre-Down Servers With EmbeddedUpdating While Running Windows Press the Down Arrow until you select Data Rate then press EMC HBA Settings Driver Revision History Where to Find the Driver Installing the HBA DriverSelect have Disk Windows 2003 STORPort UpdatesExtended Error Logging by QLogic Drivers Installation Procedure for Windows NT HostsAdministrative Tools, Computer Management Installing the HBA Driver Double-click the Scsi & RAID Controllers icon Installing and Configuring the HBA Driver Upgrading to Windows 2003 from Windows 2000 or Windows NT Replacing an HBA EMC Symmetrix Masking EnabledArrays with Device Powermt restore powermt display Installing and Configuring the HBA Driver Configuring an EMC Boot Device Risks of Booting from the Storage Array Boot-from-SAN Configuration RestrictionsHow to Determine I/O Latency and Load on the Boot LUN Boot-from-SAN with Mscs Boot Crashdump Save to Disk BehaviorConfiguring the Boot Bios Configuring a Symmetrix Boot DeviceConfiguration Settings menu From the Configuration Settings menu, select Host AdapterFrom the Host Adapter Settings menu, select Host Adapter Select Current Boot Node Name and press EnterInstalling the Windows OS onto the Boot Device Installing EFI boot code onto the HBA Unload 5D Configuring an EMC Boot Device Configurable Components Drv5DCtrl60Langeng Configuring an EMC Boot Device Configuring a Symmetrix Boot Device Procedure Configuring a CLARiiON Boot DeviceFlowchart Configuring a CLARiiON Boot Device Requirements Configurations, Revisions Hardware Software RequirementsTopologies Refer to Downloading QLogic Drivers and Firmware on Preparing the Storage SystemSetting Up the HBA Bios Preparing the Fabric Configuring an EMC Boot Device What Next? Node NamePreparing the Server Boot Bios Configuring the HBAConfiguring an EMC Boot Device When the QLogic Bios banner shown in appears, press Windows Licensing Agreement appears Configuring a CLARiiON Boot Device Verifying HBA Driver and Digital Signature Installation Installing Multipath and Failover Software Assigning a Permanent Boot Drive Letter for Windows NTWhat Next? From here Installing Additional Navisphere Host Agent Software Storagegroupname y/n? Configuring an EMC Boot Device On the Computer Management window, click Disk Management Trespassing the Boot LUN Using atftrespassStarting a Fresh Installation Boot Time and LUN AvailabilityBoot Time and LUN Availability EMC Symmetrix EMC CLARiiON Replacing a Boot HBAExplanations of Entries How a Server Responds to Failure in the Boot LUN PathNtosknl Bsod Known IssuesHBA TOE Windows 2003 STORPort Updates Next dialog, click ReInstall Driver, and then, click Next Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Configuring iSNS settings for QLA4010 Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Configuring iSNS settings for QLA4010 Installing Boot Bios on the QLA4010 iSCSI HBA from DOS Select iSCSI Boot Settings Select Configuration Settings from the menuSelect iSCSI Boot Settings, and press Enter Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE Third-Party Software QLogic SANSurfer SANBlade Manager SANSurfer versions include Initial Release SANSurfer Version HistoryVeritas Volume Manager Veritas Volume Manager 3.x for WindowsVeritas Foundation Suite Veritas Volume Manager 3.1 and Veritas DMPThird-Party Software Troubleshooting Problem Problems and SolutionsSolution Later already contain this correction Flasutil Index Nvram