Contents
REV A07
Copyright 2001-2005 EMC Corporation. All rights reserved
Trademark Information
Contents
Chapter Configuring an EMC Boot Device
Chapter Installing and Configuring the QLogic QLA4010 iSCSI
Appendix B Troubleshooting
Appendix a Third-Party Software
Problem Index
EMC uses the following conventions for notes, cautions,
Damage to the system or equipment. The caution may apply to
Hardware or software
Related Documentation Typographical Conventions
Palatino
Bold
Introduction
Understanding Persistent Binding in a Fabric Environment
Understanding Persistent Binding in a Fabric Environment
HBA
Installing Configuring the HBA Driver
Introduction
Downloading QLogic Drivers Firmware Verifying Documentation
Installing an HBA
Check for an Updated HBA Driver
Reconfigure the HBA Jumper
Move the jumpers, onto pins 1-2 if not already there
Set the HBA FC-AL Loop ID
Installing an HBA
Settings
EMC HBA Settings
Pre-Configured
Settings menus
Configuring Nvram for Stratus ftServers
With Embedded
Firmware/BIOS
Fibre-Down Servers
QLogic HBAs
Updating While Running Windows
Press the Down Arrow until you select Data Rate then press
EMC HBA Settings
Installing the HBA Driver
Driver Revision History Where to Find the Driver
Installation Procedure for Windows NT Hosts
Windows 2003 STORPort Updates
Extended Error Logging by QLogic Drivers
Select have Disk
Administrative Tools, Computer Management
Installing the HBA Driver
Double-click the Scsi & RAID Controllers icon
Installing and Configuring the HBA Driver
Upgrading to Windows 2003 from Windows 2000 or Windows NT
Replacing an HBA
Masking Enabled
EMC Symmetrix
Arrays with Device
Powermt restore powermt display
Installing and Configuring the HBA Driver
Configuring an EMC Boot Device
Boot-from-SAN Configuration Restrictions
Risks of Booting from the Storage Array
How to Determine I/O Latency and Load on the Boot LUN
Boot Crashdump Save to Disk Behavior
Boot-from-SAN with Mscs
Configuring a Symmetrix Boot Device
Configuring the Boot Bios
Select Current Boot Node Name and press Enter
From the Configuration Settings menu, select Host Adapter
From the Host Adapter Settings menu, select Host Adapter
Configuration Settings menu
Installing the Windows OS onto the Boot Device
Installing EFI boot code onto the HBA
Unload 5D
Configuring an EMC Boot Device
Configurable Components Drv5DCtrl60Langeng
Configuring an EMC Boot Device
Configuring a Symmetrix Boot Device
Configuring a CLARiiON Boot Device
Procedure
Flowchart
Configuring a CLARiiON Boot Device
Configurations, Revisions Hardware Software Requirements
Requirements
Topologies
Preparing the Storage System
Refer to Downloading QLogic Drivers and Firmware on
Setting Up the HBA Bios
Preparing the Fabric
Configuring an EMC Boot Device
Node Name
What Next?
Preparing the Server
Configuring the HBA
Boot Bios
Configuring an EMC Boot Device
When the QLogic Bios banner shown in appears, press
Windows Licensing Agreement appears
Configuring a CLARiiON Boot Device
Verifying HBA Driver and Digital Signature Installation
Assigning a Permanent Boot Drive Letter for Windows NT
Installing Multipath and Failover Software
What Next? From here
Installing Additional Navisphere Host Agent Software
Storagegroupname y/n?
Configuring an EMC Boot Device
Trespassing the Boot LUN Using atftrespass
On the Computer Management window, click Disk Management
Boot Time and LUN Availability
Starting a Fresh Installation
Boot Time and LUN Availability
Replacing a Boot HBA
EMC Symmetrix EMC CLARiiON
How a Server Responds to Failure in the Boot LUN Path
Explanations of Entries
Known Issues
Ntosknl Bsod
HBA TOE
Windows 2003 STORPort Updates
Next dialog, click ReInstall Driver, and then, click Next
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Configuring iSNS settings for QLA4010
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Configuring iSNS settings for QLA4010
Installing Boot Bios on the QLA4010 iSCSI HBA from DOS
Select Configuration Settings from the menu
Select iSCSI Boot Settings
Select iSCSI Boot Settings, and press Enter
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Installing and Configuring the QLogic QLA4010 iSCSI HBA TOE
Third-Party Software
QLogic SANSurfer SANBlade Manager
SANSurfer Version History
SANSurfer versions include Initial Release
Veritas Volume Manager 3.x for Windows
Veritas Volume Manager
Veritas Volume Manager 3.1 and Veritas DMP
Veritas Foundation Suite
Third-Party Software
Troubleshooting
Problems and Solutions
Problem
Solution
Later already contain this correction
Flasutil
Index
Nvram