Extron electronic 48 manual Creating a Set of Ties, Example 1 Create a set of video and audio ties

Page 19

Creating a Set of Ties

You can create a set of ties, changing the current configuration, by using the front panel buttons. Change the current configuration as follows:

1.Select video, audio, or both to configure by pressing the I/O button as necessary.

2.Select the desired input and one or more outputs by pressing the input and output buttons.

3.Press and release the Enter button.

4.Repeat steps 1 through 3 to create additional ties until the desired configuration is complete.

NOTES: • Only one video input and one audio input can be tied to an output.

• If a tie is made between an input and an output, and the selected output was previously tied to another input, the older tie is broken in favor of the newer tie.

• Output LEDs light when an input is selected to indicate current ties. Press and release the associated output buttons to clear unwanted outputs.

• If, when you are configuring video and audio ties, the Audio LED blinks and the Video LED is on after you have selected an input or output, the LEDs indicate audio breakaway, meaning that the audio ties are not the same as the video ties for that input.

• If an input with no tie is selected, only the LED for that input lights.

• As each output is selected, the associated output LED blinks to indicate a tentative tie until you press the Enter button or the 5-second timeout expires. LEDs for outputs that were already tied to the input light steadily. Outputs that are already tied can be left on, along with new blinking selections, or toggled off by pressing the associated output button.

• If you inadvertently press the wrong input or output button, wait approximately 5 seconds. The input and output button selections time out and are abandoned.

Example 1: Create a set of video and audio ties

In the following example, input 5 is tied to outputs 3, 4, and 8. The example shows the front panel indications that result from your actions.

NOTE: This example assumes that there are no ties in the current configuration.

1.Select video and audio for the tie: If necessary, press and release the I/O button to cycle through the selections until the both LEDs light.

Press the button.

I/O

The video LED lights when video is selected. VID

The audio LED lights when audio is selected. AUD

2.Select an input: Press and release the input 5 button.

Press and release the Input 5 button.

INPUTS

1

 

2

3

 

4

 

5

 

 

6

 

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The Input 5 LED lights to indicate that input 5 is selected.

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Operation 13

Page 18 Page 20
Image 19
Page 18 Page 20
Contents MVX 44 / 48 / 84 / 88 Series Safety Instructions English FCC Class a Notice Variables are written in slanted form as shown here Conventions Used in this GuideExtron Electronics. All rights reserved Contents MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Contents About this Guide About the SwitchersAny input to any or all outputs FeaturesMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction Cabling and Rear Panel Views Mounting the SwitcherVideo and Audio Output Connections Video and Audio Input ConnectionsRS-232 Port Pin Assignment Remote ConnectionPower Connection MVX 88 VGA a Front Panel Front Panel Controls and IndicatorsInput and Output Selection Controls and Indicators Infrared Sensor and Power/audio/data LEDPower/data/audio LED Video/+dB LED and Audio/-dB LED Selection and Audio/video Controls and IndicatorsO and Audio Setup button Control Buttons and LEDsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Operations Powering up the SwitcherDefinitions Example 1 Create a set of video and audio ties Creating a Set of TiesSelect an input Press and release the input 5 button Confirm the change Press and release the Enter button Example 1 ConfigurationSelect the output Press and release the output 1 button Example 2 Add a video tie to a set of video and audio tiesSelect the output Press and release the output 4 button Example 3 Remove a tie from a set of tiesExample 4 View ties by selecting an input Viewing the ConfigurationDeselect audio Press and release the I/O button Press and release the Output 3 button Example 5 View ties by selecting outputsUsing Presets Preset Locations by Matrix Size Example 6 Save a presetExample 7 Recall a preset Audio Gain and Attenuation Adjusting Input Audio Gain and AttenuationSeconds Example 8 Adjust the input audio gainInput 5 LED lights to Adjust the Input Audio Level Example 9 Resetting audio gain single input Front Panel Security Lockout Executive Mode Setting the Output Audio LevelClear all Ties and Presets Clearing all Ties and PresetsMemory Resetting the System to Factory DefaultsOptimizing the Audio TroubleshootingWorksheet Example 1 System Equipment WorksheetsWorksheet Example 2 Daily Configuration Worksheet Example 2 Daily ConfigurationWorksheet Example 3 Test Configuration Worksheet Example 3 Test ConfigurationOutput destinations Configuration WorksheetSmall Matrix IR Remote Control IR Remote ControlSwitcher-initiated Messages Host-to-Switcher InstructionsSimple Instruction Set Control Using the Command and Response Table Switcher Error ResponsesCommands are not case sensitive X1! = Symbol definitionsCommand and Response Table for SIS Commands X1 =Command/Response Table for SIS Commands Directly write a global preset Save, recall, and directly write global presetsRGB delay View ties, gains, mutes, and presetsInformation requests Front panel lockout Executive modeResets Firmware uploadClick the Files of type drop box and select All files Loading Firmware Using an SIS CommandSelect the Firmware Upgrade File Installing the Software Matrix Switchers Control ProgramComm Port Selection window appears Using the SoftwareTo run the Matrix Switchers Control Program, click Starting the SoftwareMatrix Switchers Control Program Window no Ties Updating the Firmware Location of Firmware Upgrade FilesDownloading Firmware Upgrade Files Extron Firmware Loader Window Windows menus Windows Buttons, Drop Boxes, and Trash CanClick Exit to close the Firmware Loader Tools menu Audio Input Configuration selection Master-Reset selection Using the Help System Using Emulation ModeChoose Emulate, and click OK Reference Information SpecificationsVideo output Audio input Included Parts Part Numbers and AccessoriesMatrix switcher part numbers Part Number MVX Part NumbersCables Optional AccessoriesBulk cable and termination tools VGA male-to-female cables Part Number Terminated cable assembliesVGA male-to-male cables Part Number VGA male-to-male with audio cables Part NumberUL Rack-Mounting Guidelines Tabletop UseMounting Instructions Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East
Related manuals
Manual 78 pages 29.23 Kb

48, MVX 84, MVX 44, MVX 88 specifications

Extron Electronics is a prominent leader in high-quality AV technology solutions, renowned for its innovative product lines designed to address diverse connectivity and distribution needs. Among their array of offerings, the MVX series stands out, particularly the MVX 44, MVX 84, and MVX 88 models, which cater to various AV signal routing needs within educational institutions, corporate environments, and large spaces.

The Extron MVX 44 is a 4x4 matrix switcher designed for routing HDMI, VGA, and audio signals. One of its key features is its ability to deliver high-resolution video up to 1080p, making it ideal for modern multimedia presentations. The MVX 44 supports EDID management, ensures compatibility with a range of source devices, and features automatic switching capabilities. It also includes a user-friendly interface for seamless operation, allowing simultaneous switching of multiple input sources to multiple outputs.

Expanding on the capabilities of the MVX 44, the MVX 84 and MVX 88 models provide enhanced functionality with additional inputs and outputs. The MVX 84 offers support for up to 8 input sources and 4 output destinations, while the MVX 88 offers 8x8 routing of signals. Both models maintain superior video quality and high-performance signal processing, accommodating more extensive AV systems. They also share features such as HDCP compliance to secure content protection, ensuring that the highest quality video signals are transmitted without degradation.

Technologically advanced, these switchers incorporate Extron's exclusive technologies, such as the Advanced Color Processing for superior color fidelity and signal reliability. Additionally, the Series comes equipped with optional control and integration capabilities, enabling connection to various AV control systems for centralized management.

The Extron MVX series matrices are built with the robustness expected from Extron products, ensuring long-term reliability in demanding environments. The integration of state-of-the-art support for audio signals allows not only video but also audio distribution, making them versatile for any AV setup. In summary, with their rich feature set, impressive scalability, and superior video processing capabilities, the Extron MVX 44, MVX 84, and MVX 88 present compelling solutions for anyone looking to streamline AV signal management in professional setups.
Top Page Image Contents