Extron electronic 48, MVX 88, MVX 44, MVX 84 manual Select the Firmware Upgrade File

Page 51

Ensure that the firmware upgrade is for the MVX Series AV switcher. Valid firmware files must have the file extension “.s19”. Any other file extension is not a firmware upgrade for your switcher.

6.Navigate to the folder where you saved the firmware upgrade file. Select the file (see figure 23).

NOTE:

Figure 23. Select the Firmware Upgrade File

7.Click Open. The firmware upload begins. If you have the echo function of HyperTerminal turned on, HyperTerminal will display a scroll of the text of the firmware file as it uploads to the switcher (see figure 24).

Figure 24. Upload Progress Display

8.After several minutes, the switcher reports the startup copyright message:

(C) Copyright 20yy, Extron Electronics “MVX nn VGA/A Series”, Vx.xx]

This message indicates that the firmware upload is complete.

9.Exit HyperTerminal.

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Remote Operation 45

Image 51

Contents MVX 44 / 48 / 84 / 88 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Variables are written in slanted form as shown hereExtron Electronics. All rights reserved Contents MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Contents About this Guide About the SwitchersAny input to any or all outputs FeaturesMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction Cabling and Rear Panel Views Mounting the SwitcherVideo and Audio Output Connections Video and Audio Input ConnectionsRS-232 Port Pin Assignment Remote ConnectionPower Connection MVX 88 VGA a Front Panel Front Panel Controls and IndicatorsInfrared Sensor and Power/audio/data LED Input and Output Selection Controls and IndicatorsPower/data/audio LED Video/+dB LED and Audio/-dB LED Selection and Audio/video Controls and IndicatorsO and Audio Setup button Control Buttons and LEDsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Powering up the Switcher OperationsDefinitions Creating a Set of Ties Example 1 Create a set of video and audio tiesSelect an input Press and release the input 5 button Confirm the change Press and release the Enter button Example 1 ConfigurationSelect the output Press and release the output 1 button Example 2 Add a video tie to a set of video and audio tiesSelect the output Press and release the output 4 button Example 3 Remove a tie from a set of tiesExample 4 View ties by selecting an input Viewing the ConfigurationDeselect audio Press and release the I/O button Press and release the Output 3 button Example 5 View ties by selecting outputsUsing Presets Preset Locations by Matrix Size Example 6 Save a presetExample 7 Recall a preset Audio Gain and Attenuation Adjusting Input Audio Gain and AttenuationSeconds Example 8 Adjust the input audio gainInput 5 LED lights to Adjust the Input Audio Level Example 9 Resetting audio gain single input Front Panel Security Lockout Executive Mode Setting the Output Audio LevelClear all Ties and Presets Clearing all Ties and PresetsMemory Resetting the System to Factory DefaultsOptimizing the Audio TroubleshootingWorksheet Example 1 System Equipment WorksheetsWorksheet Example 2 Daily Configuration Worksheet Example 2 Daily ConfigurationWorksheet Example 3 Test Configuration Worksheet Example 3 Test ConfigurationOutput destinations Configuration WorksheetSmall Matrix IR Remote Control IR Remote ControlHost-to-Switcher Instructions Switcher-initiated MessagesSimple Instruction Set Control Switcher Error Responses Using the Command and Response TableCommands are not case sensitive X1! = Symbol definitionsCommand and Response Table for SIS Commands X1 =Command/Response Table for SIS Commands Directly write a global preset Save, recall, and directly write global presets RGB delay View ties, gains, mutes, and presetsInformation requests Front panel lockout Executive modeResets Firmware uploadClick the Files of type drop box and select All files Loading Firmware Using an SIS CommandSelect the Firmware Upgrade File Installing the Software Matrix Switchers Control ProgramComm Port Selection window appears Using the SoftwareTo run the Matrix Switchers Control Program, click Starting the SoftwareMatrix Switchers Control Program Window no Ties Updating the Firmware Location of Firmware Upgrade FilesDownloading Firmware Upgrade Files Extron Firmware Loader Window Windows Buttons, Drop Boxes, and Trash Can Windows menusClick Exit to close the Firmware Loader Tools menu Audio Input Configuration selection Master-Reset selection Using Emulation Mode Using the Help SystemChoose Emulate, and click OK Reference Information SpecificationsVideo output Audio input Included Parts Part Numbers and AccessoriesMatrix switcher part numbers Part Number MVX Part NumbersOptional Accessories CablesBulk cable and termination tools VGA male-to-female cables Part Number Terminated cable assembliesVGA male-to-male cables Part Number VGA male-to-male with audio cables Part NumberTabletop Use UL Rack-Mounting GuidelinesMounting Instructions Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East

Related manuals

Manual 78 pages 29.23 Kb