Extron electronic MVX 84, MVX 88, MVX 44, 48 manual Example 8 Adjust the input audio gain, Seconds

Page 30

By noting the status of these LEDs and counting the number of 1 dB steps you increase or decrease the audio level (step 4 and example 8, step 2a), you can determine the exact input gain or attenuation setting.

b.The Power LED blinks to indicate the adjusted audio level (compared to the internal level, -10 dBV):

When the LED is lit most of the time, blinking off only occasionally, the level is too high.

When the LED is off most of the time, blinking on (lit) only occasionally, the level is too low.

When the LED blinks frequently, the level is in the proper range.

c.The < LED lights steadily when the adjustment is at the minimum level (maximum attenuation, -18 dB). The > LED lights steadily when the adjustment is at the maximum gain (+10 dB).

4.Press and release the < and > buttons to increase and decrease the audio level by 1 dB or press and hold the buttons to increase or decrease the level by 3 dB per second. The < or > LEDs flash to indicate each 1 dB level change.

NOTE: Each time you press the < or > button, wait for the < or > LED to flash

before pushing the button again. Pressing the button too rapidly may not increment or decrement the audio level.

5.Press and release the Audio Setup button to save the level value in memory and to exit

Audio Setup mode. The Audio Setup LED turns off.

NOTES: After approximately 30 seconds of front panel inactivity, the switcher

saves the most recent input gain or attenuation levels and exits Audio

Setup mode.

There is one audio gain or attenuation setting per input. The setting is

shared by the left and right audio inputs.

The input audio gain or attenuation settings are stored in non-volatile memory. When power is removed and restored, the audio level settings are retained.

Example 8: Adjust the input audio gain

The following steps show an example in which an input audio level is viewed and adjusted. The example shows the front panel indications that result from your actions.

1.Select Audio Setup mode: Press and hold the Audio Setup (I/O) button for approximately 2 seconds.

Press and hold the button.

 

2 seconds

AUDIO SETUP

AUDIO SETUP

The LED lights to indicate Audio Setup mode.

Release the Audio Setup button.

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Operation 24

Image 30
Contents MVX 44 / 48 / 84 / 88 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Variables are written in slanted form as shown hereExtron Electronics. All rights reserved Contents MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Contents About the Switchers About this GuideFeatures Any input to any or all outputsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction Mounting the Switcher Cabling and Rear Panel ViewsVideo and Audio Input Connections Video and Audio Output ConnectionsRemote Connection RS-232 Port Pin AssignmentPower Connection Front Panel Controls and Indicators MVX 88 VGA a Front PanelInfrared Sensor and Power/audio/data LED Input and Output Selection Controls and IndicatorsPower/data/audio LED Control Buttons and LEDs Selection and Audio/video Controls and IndicatorsO and Audio Setup button Video/+dB LED and Audio/-dB LEDMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Powering up the Switcher OperationsDefinitions Creating a Set of Ties Example 1 Create a set of video and audio tiesSelect an input Press and release the input 5 button Example 1 Configuration Confirm the change Press and release the Enter buttonExample 2 Add a video tie to a set of video and audio ties Select the output Press and release the output 1 buttonExample 3 Remove a tie from a set of ties Select the output Press and release the output 4 buttonViewing the Configuration Example 4 View ties by selecting an inputDeselect audio Press and release the I/O button Example 5 View ties by selecting outputs Press and release the Output 3 buttonUsing Presets Example 6 Save a preset Preset Locations by Matrix SizeExample 7 Recall a preset Adjusting Input Audio Gain and Attenuation Audio Gain and AttenuationExample 8 Adjust the input audio gain SecondsInput 5 LED lights to Adjust the Input Audio Level Example 9 Resetting audio gain single input Setting the Output Audio Level Front Panel Security Lockout Executive ModeClearing all Ties and Presets Clear all Ties and PresetsResetting the System to Factory Defaults MemoryTroubleshooting Optimizing the AudioWorksheets Worksheet Example 1 System EquipmentWorksheet Example 2 Daily Configuration Worksheet Example 2 Daily ConfigurationWorksheet Example 3 Test Configuration Worksheet Example 3 Test ConfigurationConfiguration Worksheet Output destinationsIR Remote Control Small Matrix IR Remote ControlHost-to-Switcher Instructions Switcher-initiated MessagesSimple Instruction Set Control Switcher Error Responses Using the Command and Response TableCommands are not case sensitive X1 = Symbol definitionsCommand and Response Table for SIS Commands X1! =Command/Response Table for SIS Commands Save, recall, and directly write global presets Directly write a global presetView ties, gains, mutes, and presets RGB delayFirmware upload Front panel lockout Executive modeResets Information requestsLoading Firmware Using an SIS Command Click the Files of type drop box and select All filesSelect the Firmware Upgrade File Matrix Switchers Control Program Installing the SoftwareStarting the Software Using the SoftwareTo run the Matrix Switchers Control Program, click Comm Port Selection window appearsMatrix Switchers Control Program Window no Ties Location of Firmware Upgrade Files Updating the FirmwareDownloading Firmware Upgrade Files Extron Firmware Loader Window Windows Buttons, Drop Boxes, and Trash Can Windows menusClick Exit to close the Firmware Loader Tools menu Audio Input Configuration selection Master-Reset selection Using Emulation Mode Using the Help SystemChoose Emulate, and click OK Specifications Reference InformationVideo output Audio input MVX Part Numbers Part Numbers and AccessoriesMatrix switcher part numbers Part Number Included PartsOptional Accessories CablesBulk cable and termination tools VGA male-to-male with audio cables Part Number Terminated cable assembliesVGA male-to-male cables Part Number VGA male-to-female cables Part NumberTabletop Use UL Rack-Mounting GuidelinesMounting Instructions Asia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe
Related manuals
Manual 78 pages 29.23 Kb

48, MVX 84, MVX 44, MVX 88 specifications

Extron Electronics is a prominent leader in high-quality AV technology solutions, renowned for its innovative product lines designed to address diverse connectivity and distribution needs. Among their array of offerings, the MVX series stands out, particularly the MVX 44, MVX 84, and MVX 88 models, which cater to various AV signal routing needs within educational institutions, corporate environments, and large spaces.

The Extron MVX 44 is a 4x4 matrix switcher designed for routing HDMI, VGA, and audio signals. One of its key features is its ability to deliver high-resolution video up to 1080p, making it ideal for modern multimedia presentations. The MVX 44 supports EDID management, ensures compatibility with a range of source devices, and features automatic switching capabilities. It also includes a user-friendly interface for seamless operation, allowing simultaneous switching of multiple input sources to multiple outputs.

Expanding on the capabilities of the MVX 44, the MVX 84 and MVX 88 models provide enhanced functionality with additional inputs and outputs. The MVX 84 offers support for up to 8 input sources and 4 output destinations, while the MVX 88 offers 8x8 routing of signals. Both models maintain superior video quality and high-performance signal processing, accommodating more extensive AV systems. They also share features such as HDCP compliance to secure content protection, ensuring that the highest quality video signals are transmitted without degradation.

Technologically advanced, these switchers incorporate Extron's exclusive technologies, such as the Advanced Color Processing for superior color fidelity and signal reliability. Additionally, the Series comes equipped with optional control and integration capabilities, enabling connection to various AV control systems for centralized management.

The Extron MVX series matrices are built with the robustness expected from Extron products, ensuring long-term reliability in demanding environments. The integration of state-of-the-art support for audio signals allows not only video but also audio distribution, making them versatile for any AV setup. In summary, with their rich feature set, impressive scalability, and superior video processing capabilities, the Extron MVX 44, MVX 84, and MVX 88 present compelling solutions for anyone looking to streamline AV signal management in professional setups.