Extron electronic MVX 44, MVX 88, MVX 84, 48 manual Extron Firmware Loader Window

Page 57

7.Connect a computer that runs the Windows operating system to the switcher serial port

(see “Installation” for more details).

8.Start the Matrix Switchers Control Program and connect to the matrix switcher. See “Starting the Software,” on page 47.

9.Click Tools > Update firmware. The Extron Firmware Loader appears (see figure 32).

10

Figure 32. Extron Firmware Loader Window

10.Select the MVX matrix switcher and click File > Open. The Choose Firmware File screen appears (see figure 33).

11

11

Figure 33. Choose Firmware File Window

11.Navigate to and select the new firmware file. Click Open. The Choose Firmware File window closes.

CAUTION: The firmware file must have an .s19 extension. Other file types can cause the switcher to stop functioning.

NOTES: • When downloaded from the Extron website, the firmware is placed in a

subfolder of C:\Program Files\Extron\Firmware.

• Valid firmware files must have the file extension .S19. A file with any

other extension is not a firmware upgrade.

• The original factory-installed firmware is permanently available on the matrix switcher. If the attempted firmware upload fails for any reason, the switcher reverts to the factory-installed firmware.

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Remote Operation 51

Image 57

Contents MVX 44 / 48 / 84 / 88 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Variables are written in slanted form as shown hereExtron Electronics. All rights reserved Contents MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Contents About this Guide About the SwitchersAny input to any or all outputs FeaturesMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction Cabling and Rear Panel Views Mounting the SwitcherVideo and Audio Output Connections Video and Audio Input ConnectionsRS-232 Port Pin Assignment Remote ConnectionPower Connection MVX 88 VGA a Front Panel Front Panel Controls and IndicatorsInfrared Sensor and Power/audio/data LED Input and Output Selection Controls and IndicatorsPower/data/audio LED O and Audio Setup button Selection and Audio/video Controls and IndicatorsControl Buttons and LEDs Video/+dB LED and Audio/-dB LEDMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Powering up the Switcher OperationsDefinitions Creating a Set of Ties Example 1 Create a set of video and audio tiesSelect an input Press and release the input 5 button Confirm the change Press and release the Enter button Example 1 ConfigurationSelect the output Press and release the output 1 button Example 2 Add a video tie to a set of video and audio tiesSelect the output Press and release the output 4 button Example 3 Remove a tie from a set of tiesExample 4 View ties by selecting an input Viewing the ConfigurationDeselect audio Press and release the I/O button Press and release the Output 3 button Example 5 View ties by selecting outputsUsing Presets Preset Locations by Matrix Size Example 6 Save a presetExample 7 Recall a preset Audio Gain and Attenuation Adjusting Input Audio Gain and AttenuationSeconds Example 8 Adjust the input audio gainInput 5 LED lights to Adjust the Input Audio Level Example 9 Resetting audio gain single input Front Panel Security Lockout Executive Mode Setting the Output Audio LevelClear all Ties and Presets Clearing all Ties and PresetsMemory Resetting the System to Factory DefaultsOptimizing the Audio TroubleshootingWorksheet Example 1 System Equipment WorksheetsWorksheet Example 2 Daily Configuration Worksheet Example 2 Daily ConfigurationWorksheet Example 3 Test Configuration Worksheet Example 3 Test ConfigurationOutput destinations Configuration WorksheetSmall Matrix IR Remote Control IR Remote ControlHost-to-Switcher Instructions Switcher-initiated MessagesSimple Instruction Set Control Switcher Error Responses Using the Command and Response TableCommands are not case sensitive Command and Response Table for SIS Commands Symbol definitionsX1 = X1! =Command/Response Table for SIS Commands Directly write a global preset Save, recall, and directly write global presetsRGB delay View ties, gains, mutes, and presetsResets Front panel lockout Executive modeFirmware upload Information requestsClick the Files of type drop box and select All files Loading Firmware Using an SIS CommandSelect the Firmware Upgrade File Installing the Software Matrix Switchers Control ProgramTo run the Matrix Switchers Control Program, click Using the SoftwareStarting the Software Comm Port Selection window appears Matrix Switchers Control Program Window no Ties Updating the Firmware Location of Firmware Upgrade FilesDownloading Firmware Upgrade Files Extron Firmware Loader Window Windows Buttons, Drop Boxes, and Trash Can Windows menusClick Exit to close the Firmware Loader Tools menu Audio Input Configuration selection Master-Reset selection Using Emulation Mode Using the Help SystemChoose Emulate, and click OK Reference Information SpecificationsVideo output Audio input Matrix switcher part numbers Part Number Part Numbers and AccessoriesMVX Part Numbers Included PartsOptional Accessories CablesBulk cable and termination tools VGA male-to-male cables Part Number Terminated cable assembliesVGA male-to-male with audio cables Part Number VGA male-to-female cables Part NumberTabletop Use UL Rack-Mounting GuidelinesMounting Instructions Europe, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East Europe

Related manuals

Manual 78 pages 29.23 Kb