Extron electronic 48, MVX 88, MVX 44, MVX 84 manual Reference Information, Specifications

Page 63

Reference

Information

This section discusses the specifications, part numbers, and accessories for the

MVX Matrix Switchers. Topics that are covered include:

•Specifications

•Part Numbers and Accessories

•Mounting the Switcher

Specifications

Video

Routing

MVX 44 VGA A�� 4 x 4 matrix

MVX 48 VGA A�� 4 x 8 matrix

MVX 84 VGA A�� 8 x 4 matrix

MVX 88 VGA A�� 8 x 8 matrix

Gain �� Unity

Bandwidth�� 350 MHz (-3 dB), fully loaded

0	- 10 MHz ��	No more than +0.14 dB to -0.1 dB
0	- 130 MHz ��	No more than +0.95 dB to -0.8 dB

Crosstalk�� <-60 dB nominal @ 10 MHz, <-39 dB @ 100 MHz

Switching speed �� 20 ms (max.)

Video input

Number/signal type�� VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HDTV, component video (bi-level and tri-level sync), S-video, composite video

44/48 models ��	4
84/88 models ��	8
Connectors
44/48 models ��	4 female 15-pin HD
84/88 models ��	8 female 15-pin HD
Nominal level ��	1 Vp-p for Y of component video and S-video, and for composite video
	0.7 Vp-p for RGB and for R-Y and B-Y of component video
	0.3 Vp-p for C of S-video
Minimum/maximum levels��	Analog: 0.3 V to 2.0 Vp-p with no offset at unity gain
Impedance��	75 ohms
Horizontal frequency��	15 kHz to 145 kHz
Vertical frequency��	30 Hz to 170 Hz
Return loss��	<-40 dB @ 5 MHz
DC offset (max. allowable) ��	1.5 V

MVX 44 / 48 / 84 / 88 VGA Matrix Switchers • Reference Information 57

Image 63

Contents MVX 44 / 48 / 84 / 88 Series Safety Instructions English FCC Class a Notice Conventions Used in this Guide Variables are written in slanted form as shown hereExtron Electronics. All rights reserved Contents MVX 44 / 48 / 84 / 88 VGA Matrix Switchers Contents About this Guide About the SwitchersAny input to any or all outputs FeaturesMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Introduction Cabling and Rear Panel Views Mounting the SwitcherVideo and Audio Output Connections Video and Audio Input ConnectionsRS-232 Port Pin Assignment Remote ConnectionPower Connection MVX 88 VGA a Front Panel Front Panel Controls and IndicatorsInfrared Sensor and Power/audio/data LED Input and Output Selection Controls and IndicatorsPower/data/audio LED Video/+dB LED and Audio/-dB LED Selection and Audio/video Controls and IndicatorsO and Audio Setup button Control Buttons and LEDsMVX 44 / 48 / 84 / 88 VGA Matrix Switchers Operation Powering up the Switcher OperationsDefinitions Creating a Set of Ties Example 1 Create a set of video and audio tiesSelect an input Press and release the input 5 button Confirm the change Press and release the Enter button Example 1 ConfigurationSelect the output Press and release the output 1 button Example 2 Add a video tie to a set of video and audio tiesSelect the output Press and release the output 4 button Example 3 Remove a tie from a set of tiesExample 4 View ties by selecting an input Viewing the ConfigurationDeselect audio Press and release the I/O button Press and release the Output 3 button Example 5 View ties by selecting outputsUsing Presets Preset Locations by Matrix Size Example 6 Save a presetExample 7 Recall a preset Audio Gain and Attenuation Adjusting Input Audio Gain and AttenuationSeconds Example 8 Adjust the input audio gainInput 5 LED lights to Adjust the Input Audio Level Example 9 Resetting audio gain single input Front Panel Security Lockout Executive Mode Setting the Output Audio LevelClear all Ties and Presets Clearing all Ties and PresetsMemory Resetting the System to Factory DefaultsOptimizing the Audio TroubleshootingWorksheet Example 1 System Equipment WorksheetsWorksheet Example 2 Daily Configuration Worksheet Example 2 Daily ConfigurationWorksheet Example 3 Test Configuration Worksheet Example 3 Test ConfigurationOutput destinations Configuration WorksheetSmall Matrix IR Remote Control IR Remote ControlHost-to-Switcher Instructions Switcher-initiated MessagesSimple Instruction Set Control Switcher Error Responses Using the Command and Response TableCommands are not case sensitive X1! = Symbol definitionsCommand and Response Table for SIS Commands X1 =Command/Response Table for SIS Commands Directly write a global preset Save, recall, and directly write global presetsRGB delay View ties, gains, mutes, and presetsInformation requests Front panel lockout Executive modeResets Firmware uploadClick the Files of type drop box and select All files Loading Firmware Using an SIS CommandSelect the Firmware Upgrade File Installing the Software Matrix Switchers Control ProgramComm Port Selection window appears Using the SoftwareTo run the Matrix Switchers Control Program, click Starting the SoftwareMatrix Switchers Control Program Window no Ties Updating the Firmware Location of Firmware Upgrade FilesDownloading Firmware Upgrade Files Extron Firmware Loader Window Windows Buttons, Drop Boxes, and Trash Can Windows menusClick Exit to close the Firmware Loader Tools menu Audio Input Configuration selection Master-Reset selection Using Emulation Mode Using the Help SystemChoose Emulate, and click OK Reference Information SpecificationsVideo output Audio input Included Parts Part Numbers and AccessoriesMatrix switcher part numbers Part Number MVX Part NumbersOptional Accessories CablesBulk cable and termination tools VGA male-to-female cables Part Number Terminated cable assembliesVGA male-to-male cables Part Number VGA male-to-male with audio cables Part NumberTabletop Use UL Rack-Mounting GuidelinesMounting Instructions Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East

Related manuals

Manual 78 pages 29.23 Kb