Extron electronic SW RGB, SW YUV A manual Remote connection, Power connection

Page 19

Remote connection

7Remote connector — Connect a host device, such as a computer or touch panel control, or a remote contact closure device to the switcher via this 9-pin D connector (figure 2-11) for remote control of the switcher.

See chapter 4, Remote Control, for definitions of the SIS commands, details on how to install and use the control software, and information on how to make a remote contact closure device.

5		1	Pin	RS-232	Contact closure	Function
			1	—	In #1	Input #1

			2	TX	—	Transmit data (-)
9	6		3	RX	—	Receive data (+)
Female
			4	—	In #2	Input #2
1		5
			5	Gnd	Gnd	Signal ground

			6	—	In #3	Input #3
6	9		7	—	In #4	Input #4
	Male		8	—	In #5	Input #5

			9	—	In #6	Input #6

Figure 2-11 — Remote port connector and pinout

Power connection

8AC power connector — Plug a standard IEC power cord into this connector to connect the switcher to a 100 VAC to 240 VAC, 50 or 60 Hz power source.

SW RGB and YUV A Switchers • Installation 2-9

Image 19

Contents SW RGB and SW YUV a Series Wideband and Component Video and Audio SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschSW RGB and YUV a Switchers Quick Start QS-1 Quick Start SW RGB and YUV a SwitchersQS-2 SW RGB and YUV a Switchers Quick Start Quick Start SW RGB and YUV a Switchers, cont’dSwitch mode Switch inputs in normal switch modeTable of Contents Table of Contents, cont’d One SW RGB and YUV a Switchers Introduction About the SwitchersIntroductiontroduction, cont’d RGB video models FeaturesAudio switching models All switchersAll models Introduction, cont’dTwo Rack mounting the switcher Installationstallation, cont’dInstallation Overview Mounting the SwitcherRack mounting an SW2 switcher Under furniture mounting the switcher Installation, cont’dThrough-desk mounting Through furniture mounting the switcherCabling and Rear Panel Views SW2 Rgbhv video switcherRGB and component video inputs InputsRGB and component video outputs OutputRemote connection Power connectionInstallation, cont’d Three Operationeration, cont’d Controls and IndicatorsInput selection controls and indicators SW RGB and YUV a Switchers OperationAutoswitch mode control and indicator Audio controls and indicatorsOperation, cont’d Switcher OperationsPower Switching inputsExample Viewing the audio level Example Adjusting the audio levelExample, step D Adjusting the audio level Memory Audio level reset single inputAudio level reset all inputs Optimizing the Audio SW2, SW4, and SW6 Rgbhv a onlyTroubleshooting If No Image Appears Four Simple Instruction Set Host-to-switcher instructionsSW RGB and YUV a Switchers Remote Control RemoteControl,cont’dUsing the command/response table Switcher-initiated unsolicited messagesError responses TimeoutSymbol definitions Remote Control, cont’dCommand Ascii Command Response Additional description Reset Using the software Installing the softwareWindows-Based Control Program Using the help system Infrared Remote ControlContact Closure Remote Control, cont’d AAppendix a Specifications and Part NumbersSW RGB and YUV a Switchers Specifications and Part Numbers Specificationsecifications, cont’dSync Audio output SW 2/4/6 Rgbhv a only Specifications, cont’dPart Numbers SW Rgbhv switcher part numbersSupplied accessories Optional accessoriesPre-cut cables Assorted connectors BNC connectorsPlenum BNC-5 Mini HR Cable BNC-5 RC and BNC-6 RC CableFCC Class a Notice Extron’s Warranty Extron Electronics, USA