Extron electronic SW RGB manual Example Adjusting the audio level, Example Viewing the audio level

Page 25

2. Press and hold the Audio Conf/Save button until the Conf/ Save LED begins to blink, then release the Conf/Save button.

The +dB and –dB LEDs display the polarity (+ or –). The lit +dB LED indicates a positive (gain) level. The lit –dB LED indicates a negative (attenuation) level. Both LEDs lit indicate 0 dB.

Press and hold.

B

CONF/SAVE

Conf/Save blinks. Release the button.

On the SW4 RGBHV A and SW6 RGBHV A only, the input 1 through 4 LEDs display the approximate audio level for the selected input. Each input LED indicates a range of 6 dB when lit (Input 1 LED off = 0 dB to 5 dB, Input 1 LED lit = 6 dB to 11 dB, Input 2 LED lit = 12 dB to 17 dB, and so on).

3. Press and release the and buttons to decrease and increase the audio level by 1 dB or press and hold the buttons to decrease and increase the level by 3 dB per second. The and LEDs flash to indicate each 1 dB level change.

Each time you press and release the or button, wait for the or LED to flash before pushing the button again. Pressing the button early may not decrement or increment the audio level.

4. Press and hold the Audio Conf/Save button until the Conf/Save LED turns off to save the gain value in memory and exit the audio display and adjustment mode.

1. There is one audio level setting per input. The setting is shared by the left and right audio inputs.

2. The audio level settings are stored in non-volatile memory. When power is removed and restored, the audio level settings are retained.

Example — Adjusting the audio level

The switcher must be in normal (manual) mode.

1.

Press and release an input button to select an input. The associated input

 

LED lights.

 

 

 

 

 

 

 

 

 

 

 

 

2.

Press and hold the Audio Conf/Save button until the Audio Conf/Save LED

 

starts blinking.

 

 

 

 

 

 

 

 

 

 

 

 

3.

On the SW4 RGBHV A and SW 6 RGBHV A, the input 1 through 4 LEDs

 

display the gain or attenuation value. In figure 3-4, the LED readout shows a

 

range of +6 dB to +11 dB.

 

 

 

 

 

 

 

1

 

 

2

 

 

3

 

 

4

 

 

5

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

-dB +dB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Indicates +6dB to +11dB range

LED key: = off, = on

Figure 3-4 — Example: Viewing the audio level

SW RGB and YUV A Switchers • Operation 3-5

Image 25
Contents SW RGB and SW YUV a Series Wideband and Component Video and Audio SwitchersConsignes de Sécurité Français Safety Instructions EnglishSicherheitsanleitungen Deutsch Instrucciones de seguridad EspañolSW RGB and YUV a Switchers Quick Start QS-1 Quick Start SW RGB and YUV a SwitchersSwitch mode Quick Start SW RGB and YUV a Switchers, cont’dSwitch inputs in normal switch mode QS-2 SW RGB and YUV a Switchers Quick StartTable of Contents Table of Contents, cont’d One SW RGB and YUV a Switchers Introduction About the SwitchersIntroductiontroduction, cont’d Audio switching models FeaturesAll switchers RGB video modelsAll models Introduction, cont’dTwo Installation Overview Installationstallation, cont’dMounting the Switcher Rack mounting the switcherRack mounting an SW2 switcher Under furniture mounting the switcher Installation, cont’dThrough-desk mounting Through furniture mounting the switcherCabling and Rear Panel Views SW2 Rgbhv video switcherRGB and component video inputs InputsRGB and component video outputs OutputRemote connection Power connectionInstallation, cont’d Three Input selection controls and indicators Controls and IndicatorsSW RGB and YUV a Switchers Operation Operationeration, cont’dAutoswitch mode control and indicator Audio controls and indicatorsPower Switcher OperationsSwitching inputs Operation, cont’dExample Viewing the audio level Example Adjusting the audio levelExample, step D Adjusting the audio level Audio level reset all inputs Audio level reset single inputOptimizing the Audio SW2, SW4, and SW6 Rgbhv a only MemoryTroubleshooting If No Image Appears Four SW RGB and YUV a Switchers Remote Control Host-to-switcher instructionsRemoteControl,cont’d Simple Instruction SetError responses Switcher-initiated unsolicited messagesTimeout Using the command/response tableSymbol definitions Remote Control, cont’dCommand Ascii Command Response Additional description Reset Using the software Installing the softwareWindows-Based Control Program Using the help system Infrared Remote ControlContact Closure Remote Control, cont’d AAppendix a Specifications and Part NumbersSW RGB and YUV a Switchers Specifications and Part Numbers Specificationsecifications, cont’dSync Audio output SW 2/4/6 Rgbhv a only Specifications, cont’dSupplied accessories SW Rgbhv switcher part numbersOptional accessories Part NumbersPlenum BNC-5 Mini HR Cable Assorted connectors BNC connectorsBNC-5 RC and BNC-6 RC Cable Pre-cut cablesFCC Class a Notice Extron’s Warranty Extron Electronics, USA