Extron electronic SW YUV A manual Quick Start SW RGB and YUV a Switchers

Page 3
Digital Audio
Digital Audio

Quick Start — SW RGB and YUV A Switchers

Installation

Step 1 — Remove power

Turn off power to the input and output devices, and remove the power cords from them.

Step 2 — Mounting

SW2 —

If desired, mount the switcher in a rack using an Extron 1U Universal Rack Shelf, part # 60-190-01.

If desired, mount the switcher under a desk using an Extron Under-desk Mount Kit, part #70-077-01.

If desired, mount the switcher through a desk using an Extron Through-desk Mount Kit, part #70-077-02.

SW4 or SW6 —

If desired, mount the switcher in a rack with the supplied rack ears.

If desired, mount the switcher under a desk using an Extron 1U Under-desk Mount Kit,

part #70-222-01.

Step 3 — Video Inputs

RGBHV Models — Connect up to 2, 4 or 6 RGBHV, RGBS, RGsB, or RsGsBs video or compo- nent video inputs to the Input connectors (3a).

SW6 YUV A — Connect up to 6 component video or RGsB, RsGsBs video inputs to the Input connec- tors (3b). If you are not switching digital audio, you can use the Digital Audio BNCs for the composite sync planes of RGBS video inputs.

Step 6 — Audio Outputs

SW2 RGBHV A / SW4 RGBHV A / SW6 RGBHV A:

Cable audio models for stereo audio output (6).

SW6 YUV A: Connect a digital audio device to this female BNC connector for a digital audio output. If you are not switching digital audio, you can use this connector to

output the composite sync plane of RGBS video.

3a

RGBHV

 

 

G

B

H/HV

V

RGBS

 

 

 

 

 

 

R

G

B

H/HV

V

RGsB,

 

 

 

 

 

RsGsBs,

 

 

 

 

 

Component

R

G

B

H/HV

V

3b

R-Y

Y

B-Y

Digital Audio

5

Step 4 — Video Output

RGBHV Models — Connect an RGBHV, RGBS, RGsB, or RsGsBs video or component video display or other device to the Output connectors (3a).

SW6 YUV A — Connect a component video, RGsB, or RsGsBs video display or other device to these BNC connectors (3b). If you are not switching digital audio, you can use the Digital Audio output BNC to output the sync planes of RGBS video.

Step 5 — Audio Inputs

Tip

Sleeve

Tip

Sleeve

Unbalanced Input

(high impedance)

600 ohms

Tip

Ring

Sleeve (s)

Tip

Ring

600 ohms

Balanced Input

(600 ohms)

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Input

(high impedance)

SW2 RGBHV A / SW4 RGBHV A / SW6 RGBHV A: Cable audio models for stereo audio input (5). High impedance is generally over 10 k ohms.

SW6 YUV A: Each input has a female BNC connector for a digital audio input. If you are not switching digital audio, you can use this connector to input the

composite sync plane of RGBS video.

6

Tip

See caution

Sleeve

Tip

See caution

Unbalanced Output

Tip

Ring

Sleeve (s)

Tip

Ring

Balanced Output

CAUTION Connect the sleeve to ground. Connecting the sleeve to a negative (-) terminal will damage the audio output circuits.

SW RGB and YUV A Switchers • Quick Start QS-1

Page 2 Page 4
Image 3
Page 2 Page 4
Contents SW RGB and SW YUV a Series Wideband and Component Video and Audio SwitchersInstrucciones de seguridad Español Safety Instructions EnglishConsignes de Sécurité Français Sicherheitsanleitungen DeutschSW RGB and YUV a Switchers Quick Start QS-1 Quick Start SW RGB and YUV a SwitchersQS-2 SW RGB and YUV a Switchers Quick Start Quick Start SW RGB and YUV a Switchers, cont’dSwitch mode Switch inputs in normal switch modeTable of Contents Table of Contents, cont’d One About the Switchers SW RGB and YUV a Switchers IntroductionIntroductiontroduction, cont’d RGB video models FeaturesAudio switching models All switchersAll models Introduction, cont’dTwo Rack mounting the switcher Installationstallation, cont’dInstallation Overview Mounting the SwitcherRack mounting an SW2 switcher Under furniture mounting the switcher Installation, cont’dThrough-desk mounting Through furniture mounting the switcherCabling and Rear Panel Views SW2 Rgbhv video switcherRGB and component video inputs InputsRGB and component video outputs OutputRemote connection Power connectionInstallation, cont’d Three Operationeration, cont’d Controls and IndicatorsInput selection controls and indicators SW RGB and YUV a Switchers OperationAutoswitch mode control and indicator Audio controls and indicatorsOperation, cont’d Switcher OperationsPower Switching inputsExample Viewing the audio level Example Adjusting the audio levelExample, step D Adjusting the audio level Memory Audio level reset single inputAudio level reset all inputs Optimizing the Audio SW2, SW4, and SW6 Rgbhv a onlyTroubleshooting If No Image Appears Four Simple Instruction Set Host-to-switcher instructionsSW RGB and YUV a Switchers Remote Control RemoteControl,cont’dUsing the command/response table Switcher-initiated unsolicited messagesError responses TimeoutRemote Control, cont’d Symbol definitionsCommand Ascii Command Response Additional description Reset Installing the software Using the softwareWindows-Based Control Program Infrared Remote Control Using the help systemContact Closure Remote Control, cont’d AAppendix a Specifications and Part NumbersSW RGB and YUV a Switchers Specifications and Part Numbers Specificationsecifications, cont’dSync Audio output SW 2/4/6 Rgbhv a only Specifications, cont’dPart Numbers SW Rgbhv switcher part numbersSupplied accessories Optional accessoriesPre-cut cables Assorted connectors BNC connectorsPlenum BNC-5 Mini HR Cable BNC-5 RC and BNC-6 RC CableFCC Class a Notice Extron’s Warranty Extron Electronics, USA
Top Page Image Contents