Extron electronic HSA 222C, HSA 200S Installation Overview, Preparing the Routing Template

Page 9

Installation

Installation Overview

Install and set up the HSA surface access enclosures as follows:

1If you have an unprepared mounting template, prepare the template. See “Preparing the Routing Template” in this chapter.

2If desired, install the optional RJ-45 to RJ-11 conversion kit(s) to replace one or more RJ-45 connectors with RJ-11 connectors. Refer to the appropriate RJ-45 to RJ-11 Conversion Kit manual, for either the HSA 200 models or the HSA 222 models.

3If desired, install the optional flexible conduit kit to replace the removable AC power cord. Refer to the Flexible Conduit Kit manual.

4Cut a hole in the surface where the enclosure will be installed and install the enclosure. The screw clamps secure the enclosure to the tabletop. See “Preparing the Table and Mounting the Enclosure” in this chapter.

5Run all cables necessary to support the AC power, RJ-45, and (for HSA 200 model only) video and audio connectors. Leave enough slack in the cables to connect them to the underside of the enclosure.

6Turn off all of the equipment to be connected. Ensure that the equipment connected to the RJ-45, video, and audio connectors are all turned off and disconnected from the power source.

7Connect the power, video, audio, and RJ-45 cables to the underside of the enclosure. See “Underside Features and Cabling Connections” in this chapter.

8On HSA 200SE and HSA 200CE models, set the gain switch.

9Connect and turn on the input and output devices.

10For HSA 200SE and HSA 200CE model installations, the picture should now appear and sound should be audible. If not, ensure that all devices are plugged in and receiving power. Check the cabling and gain setting, and make adjustments as needed.

11Peel the protective coating from the top surface.

Preparing the Routing Template

Extron provides a metal template for each HSA model at no charge. Appendix A lists the HSA 200 and HSA 222 template part numbers. Extron recommends using this template as a guide to cut the hole in the table where the HSA will be installed.

 

The metal routing template is reusable. Do not discard

 

this template when the installation is complete. Save it

 

for installing future HSA enclosures of the same size.

1.

Cut 1/2" x 4" strips of soft, finished lumber long enough to

 

span the distance between the desired installation location

 

on the mounting surface and the edges of the mounting

 

surface (figure 2-1).

 

Mounting

 

Surface

 

Edge

 

Minimum

 

4 Screws

 

Wood

 

Strips

 

Wood Strip

 

Height

 

4" / 10.2 cm

Mounting

Routing Template

 

Surface

 

Edge

 

 

Wood Thickness

 

0.5" / 1.3 cm

Figure 2-1 — Prepared mounting template assembly

These strips raise the routing template above the mounting surface to provide room for the router’s collar, protect the mounting surface, and extend the reach of the routing template so that it can be clamped to the edge of the surface.

2. Using four or more short wood screws, secure the

mounting template to the lumber strips.

 

Do not allow the wood screws to protrude through

CAUTION

 

the bottom of the wooden strips. Protruding screws

will mar the table when the template is used.

2-2

HSA 200/222 Series • Installation

HSA 200/222 Series • Installation

2-3

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Hideaway Surface Access Products Precautions Extron’s WarrantyFCC Class a Notice Page Table of Contents Table of Contents, cont’d HSA 200/222 Series Surface Access ProductsOne IntroductionIntroduction About the Hideaway Surface Access ProductsAbout the Extender board line driver FeaturesAll models HSA 200CE and HSA 200SE models onlyInstallation Introduction HSA 200/222 Series Surface Access ProductsTwo Installation Installation OverviewPreparing the Routing Template Preparing the table with a router Installing the HSA enclosure all Installation, cont’dAll HSA 200 models only Underside Features and Cabling ConnectionsHSA 200C and HSA 200S no Extender board only Overtightening the Philips head screws on the screwHSA 200CE and HSA 200SE Extender board only All HSA 200 and HSA 222 modelsPower connector wiring Front Panel Connectors14 Audio input connector plug Three Maintenance and ModificationsIf the image does not appear or there is no sound If the image is not displayed correctlyMaintenance and Modifications Removing and Replacing the EnclosureReplacing the Bezels While you Maintenance and Modifications, cont’dRemoving the front panel When the HSA 200 is upside-down, the latch may Ensure that AC power is disconnected beforeProcedure Servicing the HSA unitFront access panel removal HSA 222 models Removing and Replacing the Enclosure , steps 7 through Adjusting the Top PanelReference Information AAppendix aReference Information SpecificationsSurface cutout dimensions here before cutting a hole Reference Information, cont’dGeneral HSA 200C/HSA 200CE international circular models HSA Part NumbersAccessories Replacement PartsTop Plate Dimensions Reference Information, cont’d Included PartsPackaging for Shipment Appendix BPackaging for Shipment Figure B-4 HSA unit suspended in the foam Packaging for Shipment, cont’d
Related manuals
Manual 30 pages 943 b

HSA 200SE, HSA 200S, HSA 222C specifications

Extron Electronics is renowned for its innovative solutions that enhance multimedia environments. The HSA 200S, HSA 222C, and HSA 200SE are impressive audio solutions designed for varied applications, providing high-quality audio performance and flexibility.

The Extron HSA 200S is a versatile standalone audio amplifier engineered for professional AV systems. One of its main features is its capability to deliver 200 watts of power, making it suitable for medium to large spaces. It utilizes Class D amplification technology, which ensures high efficiency and low heat generation. The HSA 200S offers a range of input options, including balanced and unbalanced audio inputs, enabling seamless integration with various audio sources. Additionally, this amplifier has built-in DSP (Digital Signal Processing) that allows for equalization and dynamic range compression, ensuring optimal audio quality across different environments.

The HSA 222C takes versatility a step further. This compact amplifier features 2-channel output and can deliver up to 20 watts per channel. It is particularly well-suited for smaller environments such as classrooms and huddle spaces. The HSA 222C also boasts an integrated mixer, which allows users to combine multiple audio sources effortlessly. The amplifier includes features like automatic gain control and priority mute, providing enhanced control over audio levels for more dynamic presentations.

The Extron HSA 200SE is another significant model in this range, amplifying 200 watts of output power, similar to the HSA 200S but with additional capabilities. It supports both stereo and mono audio outputs, making it ideal for various configurations within an AV system. The HSA 200SE incorporates advanced heat management technologies, allowing for extended usage without overheating. This model also includes RS-232 control for integration into larger control systems, offering remote management for convenient audio regulation.

All three models reflect Extron's commitment to quality and user-friendly design. They come equipped with features that ensure reliable performance, such as thermal protection, short circuit protection, and a rugged chassis for increased durability. These amplifiers not only cater to modern audio needs but also align with Extron's overarching philosophy of providing the most efficient, high-performance solutions for audio visual applications. Whether for a large auditorium or a small meeting room, the HSA series delivers exceptional sound clarity and adaptability, making them a go-to choice for AV professionals.
Top Page Image Contents