Gigabyte GA-VM800PMC user manual I/O Back Panel Introduction

Page 16

English

1-6 I/O Back Panel Introduction

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple).

Parallel Port

The parallel port allows connection of a printer, scanner and other peripheral devices.

Serial Port

Devices like mouses, modems, and etc. can be connected to Serial port.

VGA Port

Monitor can be connected to VGA port.

USB Port

Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please con- tact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors.

LAN Port

The provided Internet connection is Fast Ethernet, supporting data transfer speeds of 10/100 Mbps.

Line In

Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

Connect the stereo speakers, earphone or front surround channels to this connector.

MIC In

Microphone can be connected to MIC In jack.

You can use audio software to configure 2-/4-/6- channel audio functioning.

GA-VM800PMC Motherboard

- 16 -

Image 16
Contents GA-VM800PMC GA-VM800PMC Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUMbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector Spdifio S/PDIF In/Out ConnectorSurcen Surround Center Connector FUSB1 / FUSB2 Front USB ConnectorsComb Comb Connector CI Chassis Intrusion, Case OpenBattery Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D5 F12 Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0/1 Master, Slave TimeIDE Channel 2/3 Master Floppy 3 Mode Support for Japan Area Drive aHalt on MemoryInit Display First Hard Disk Boot PriorityVGA Share Memory Size First / Second / Third Boot Device Password CheckCPU Hyper-Threading Note Limit Cpuid Max. to 3 NoteOnBoard LAN Boot ROM Sata ModeOnChip Serial ATA AC97 AudioParallel Port Mode EPP Mode SelectUSB 2.0 Controller USB Keyboard SupportPower Management Setup Mouse Power On Resume by AlarmPME Event Wake Up Modem Ring ResumePnP/PCI Configurations Current VoltageV Vcore / DDR Power / +3.3V / +12V System / CPU TemperatureSystem Warning Temperature Case OpenedSYS / CPU FAN Fail Warning CPU Warning TemperatureCPU Smart FAN Control Note Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2Boot from CD/DVD F9 Xpress Recovery2 System requirementsPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish To configure Sata hard drives, follow the steps below Configuring Sata Hard DrivesInstall Sata hard drives in your system RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System