Gigabyte GA-VM800PMC user manual Step Save and exit Bios Setup

Page 63

Step 2:

Set First Boot Device under the Advanced BIOS Features menu to CDROM to boot from CD-ROM after system restarts (Figure 2).

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

Advanced BIOS Features

English

Init Display First

[PCI Slot]

VGA Share Memory Size

[64M]

Hard Disk Boot Priority

[Press Enter]

First Boot Device

[CDROM]

Second Boot Device

[Hard Disk]

Third Boot Device

[CDROM]

Password Check

[Setup]

CPU Hyper-Threading

[Enabled]

Limit CPUID Max. to 3

[Disabled]

No-Execute Memory Protect

[Enabled]

Virtualization Technology

[Enabled]

Item Help

Menu Level

: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

F5: Previous Values

F6: Fail-Safe Defaults

F7: Optimized Defaults

 

Figure 2

Step 3:

Save and exit BIOS Setup.

- 63 -

Appendix

Image 63
Contents GA-VM800PMC GA-VM800PMC Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSpdifio S/PDIF In/Out Connector Cdin CD in ConnectorFUSB1 / FUSB2 Front USB Connectors Surcen Surround Center ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D5„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupTime IDE Channel 0/1 Master, SlaveIDE Channel 2/3 Master Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onHard Disk Boot Priority Init Display FirstVGA Share Memory Size Limit Cpuid Max. to 3 Note First / Second / Third Boot DevicePassword Check CPU Hyper-Threading NoteAC97 Audio OnBoard LAN Boot ROMSata Mode OnChip Serial ATAUSB Keyboard Support Parallel Port ModeEPP Mode Select USB 2.0 ControllerPower Management Setup Modem Ring Resume Mouse Power OnResume by Alarm PME Event Wake UpPnP/PCI Configurations Case Opened Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem / CPU Temperature System Warning TemperatureCPU Warning Temperature SYS / CPU FAN Fail WarningCPU Smart FAN Control Note Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Configuring Sata Hard Drives To configure Sata hard drives, follow the steps belowInstall Sata hard drives in your system RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System