Gigabyte GA-VM800PMC user manual Xpress Recovery2 Introduction, System requirements

Page 50

English

4-1-2 Xpress Recovery2 Introduction

Xpress Recovery2 is designed to provide quick backup and restora- tion of hard disk data. Supporting Microsoft operating systems including Windows XP/2000/NT/98/Me and DOS, and file systems including FAT16, FAT32, and NTFS, Xpress Recovery2 is able to back up data

on hard disks on PATA and SATA IDE controllers. After Xpress Recovery2 is executed from CD-ROM for the first time, it will stay permanent in your hard disk. If you wish to run Xpress Recovery2 later, you can simply press F9 during system bootup to enter Xpress Recovery2 without the CD-ROM.

System requirements:

1.Intel x86 platforms

2.At least 64M bytes of system memory

3.VESA-supported VGA cards

How to use the Xpress Recovery2

Initial access by booting from CD-ROM and subsequent access by pressing the F9 key:

Steps: After entering BIOS Setup, go to Advanced BIOS Feature and set to boot from CD-ROM. Save the settings and exit the BIOS Setup. Insert the provided driver CD into your CD-ROM drive. Upon system restart, the message which says "Boot from CD/DVD:" will appear in the bottom left corner of the screen. Press any key to enter Xpress Recovery2.

After the steps above are completed, subsequent access to Xpress Recovery2 can be made by simply pressing the <F9> key during system power-on.

.

.

Boot from CD/DVD:

Press any key to startup XpressRecovery2.....

Award Modular BIOS v6.00PG, An Energy Star Ally

Copyright (C) 1984-2006, Award Software, Inc.

VM800PMC D5

.

.

.

.

<DEL>:BIOS Setup/Q-Flash, <F9>: Xpress Recovery2, <F12>: Boot Menu

10/31/2006-P4M800Pro-823-6A7L6G0FC-00

Boot from CD/DVD:

<F9>: Xpress Recovery2

1.If you have already entered Xpress Recovery2 by booting from the CD-ROM, you can enter Xpress Recovery2 by pressing the <F9> key in the future.

2.System storage capacity and the reading/writing speed of the hard disk will affect the data backup speed.

3.It is recommended that Xpress Recovery2 be immediately installed once you com- plete installations of OS and all required drivers as well as software.

GA-VM800PMC Motherboard

- 50 -

Image 50
Contents GA-VM800PMC GA-VM800PMC Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUMbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction EnglishATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATA0 / SATA1 Serial ATA ConnectorFpanel Front Panel Connector Faudio Front Audio Panel Connector PwrledCdin CD in Connector Spdifio S/PDIF In/Out ConnectorSurcen Surround Center Connector FUSB1 / FUSB2 Front USB ConnectorsComb Comb Connector CI Chassis Intrusion, Case OpenBattery Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D5 F12 Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 2/3 Master TimeIDE Channel 0/1 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a MemoryVGA Share Memory Size Hard Disk Boot PriorityInit Display First CPU Hyper-Threading Note First / Second / Third Boot DevicePassword Check Limit Cpuid Max. to 3 NoteOnChip Serial ATA OnBoard LAN Boot ROMSata Mode AC97 AudioUSB 2.0 Controller Parallel Port ModeEPP Mode Select USB Keyboard SupportPower Management Setup PME Event Wake Up Mouse Power OnResume by Alarm Modem Ring ResumePnP/PCI Configurations System Warning Temperature Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem / CPU Temperature Case OpenedCPU Smart FAN Control Note CPU Warning TemperatureSYS / CPU FAN Fail Warning Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction Boot from CD/DVD F9 Xpress Recovery2 Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Channel Audio Setup 5 2 / 4 / 6 Channel Audio Function IntroductionChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System