Gigabyte GA-VM800PMC USB 2.0 Controller, USB Keyboard Support, USB Mouse Support, EPP Mode Select

Page 35

USB 2.0 Controller

Disabled

Disable USB 2.0 controller.

Enabled

Enable USB 2.0 controller. (Default value)

USB Keyboard Support

Enabled

Enable USB keyboard support.

Disabled

Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled

Enable USB mouse support.

Disabled

Disable USB mouse support. (Default value)

Legacy USB storage detect

This option allows users to decide whether to detect USB storage devices, including USB flash drives and USB hard drives during POST.

Enabled

BIOS will scan all USB storage devices. (Default value)

Disabled

Disable this function.

Onboard Serial Port 1

Auto

BIOS will automatically setup the Serial port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8/IRQ3.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8/IRQ3.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically set up the Serial port 2 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8/IRQ4.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8/IRQ4.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8/IRQ3.

Disabled

Disable onboard Serial port 2.

Onboard Parallel Port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port. (Default value)

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port.

ECP+EPP

Using Parallel port as ECP and EPP mode.

EPP Mode Select

EPP1.7

Set EPP Mode to EPP1.7. (Default value)

EPP1.9

Set EPP Mode to EPP1.9.

English

- 35 -

BIOS Setup

Image 35
Contents GA-VM800PMC GA-VM800PMC Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-VM800PMC Motherboard Layout Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0 / SATA1 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSpdifio S/PDIF In/Out Connector Cdin CD in ConnectorFUSB1 / FUSB2 Front USB Connectors Surcen Surround Center ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. D5„ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 2/3 Master TimeIDE Channel 0/1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onVGA Share Memory Size Hard Disk Boot PriorityInit Display First Limit Cpuid Max. to 3 Note First / Second / Third Boot DevicePassword Check CPU Hyper-Threading NoteAC97 Audio OnBoard LAN Boot ROMSata Mode OnChip Serial ATAUSB Keyboard Support Parallel Port ModeEPP Mode Select USB 2.0 ControllerPower Management Setup Modem Ring Resume Mouse Power OnResume by Alarm PME Event Wake UpPnP/PCI Configurations Case Opened Current VoltageV Vcore / DDR Power / +3.3V / +12VSystem / CPU Temperature System Warning TemperatureCPU Smart FAN Control Note CPU Warning TemperatureSYS / CPU FAN Fail Warning Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Install Sata hard drives in your system Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below RAID Step Save and exit Bios Setup Configuring RAID set in RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Making a Sata Driver Disk Installing Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System